Login    Register
User Information
Username:
Password:
We are a free and open
community, all are welcome.
Click here to Register
Sponsored
Who is online

In total there are 62 users online :: 3 registered, 0 hidden and 59 guests


Most users ever online was 218 on Wed Dec 07, 2016 6:58 pm

Registered users: Bing [Bot], Google [Bot], Yahoo [Bot] based on users active over the past 5 minutes

The Team
Administrators
Global Moderators
global_moderators.png CS

Replacement Part NEEDED!!

This area is for the discussion of BB or airsoft sub machine guns, and or other small arms such as pellets.
Sponsored 
  • Author
    Message

Replacement Part NEEDED!!

Unread postAuthor: AxelTheWicked » Fri Jul 23, 2010 6:37 pm

ok, here's the situation; i need a replacement part for my airsoft pistol
but i can't seem to find one anywhere, probably because nobody ever figured it would break and need replacing. the part that i need to replace is the small rubber piece that goes at the base of the inside of the barrel in the gun's inner workings. (i had to take my gun apart to get the thing out cuz it tore and a BB got jammed in there)
does anyone know where i can find a replacement part for this gun?
  • 0

Attachments
IMAG0014.JPG
my airsoft pistol (UA-956)
IMAG0016.JPG
here's a view of the part i need to replace. it may not look like it but it's actually torn.
IMAG0018.JPG
another view of the part that needs replacement.
Yea, as I walk through the shadow of the Valley of Death, I shall not fear because I am the baddest motherfucker in the Valley.

AxelTheWicked
Private
Private
 
Posts: 10
Joined: Sun Aug 16, 2009 5:43 am
Location: Santa Clara, California
Country: United States (us)
Reputation: 0

Unread postAuthor: Gun Freak » Fri Jul 23, 2010 6:40 pm

Tip, use the macro button on the camera to take close ups, it looks like a flower. Is that the piece that holds the bb in place until the spring generates enough pressure to blast it out? I think you can just replace it with a small o-ring, but if not, I think you can use a small diameter rubber tube cut to the right length, and epoxy it in place.
  • 0

OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna"M16 BBMGPengunHammer Valve Airsoft SniperHigh Pressure .22 Coax
Holy Shat!
User avatar
Gun Freak
Lieutenant General
Lieutenant General
 
Posts: 4969
Joined: Mon Jan 25, 2010 4:38 pm
Location: Florida
Country: United States (us)
Reputation: 11

Unread postAuthor: clemsonguy1125 » Fri Jul 23, 2010 6:55 pm

You could see if your hardware store carries silicone tubing the right size.
  • 0

That is all.
User avatar
clemsonguy1125
Major General
Major General
 
Posts: 1485
Joined: Tue Jul 21, 2009 4:00 pm
Location: East Coast
Reputation: 1

Unread postAuthor: FighterAce » Fri Jul 23, 2010 6:59 pm

An O ring wont work because one side of this rubber is over the barrel and the other one is slightly smaller then the barrels ID... On the other hand if you epoxy it right it just might work :D You could even buy one of those cheap $2 springer pistols and extract it from it... far less expensive if you dont already have some epoxy or superglue.
  • 0

User avatar
FighterAce
1st Lieutenant
1st Lieutenant
 
Posts: 286
Joined: Fri Oct 23, 2009 1:28 pm
Location: Croatia/Zagreb
Country: Croatia (hr)
Reputation: 1

Unread postAuthor: jamie e » Fri Jul 23, 2010 11:32 pm

Looks to me like a hop-up rubber.
You might want to email an online airsoft shop like airsoft gi or go to an airsoft forum, they will probibly point you in the right direction.
  • 0

User avatar
jamie e
Private First Class
Private First Class
 
Posts: 36
Joined: Sat Dec 27, 2008 1:32 pm
Location: auckland New Zealand
Reputation: 0

Unread postAuthor: AxelTheWicked » Fri Jul 23, 2010 11:41 pm

thannks for all of your suggestions, everyone. i alredy went ahead and ordered a cheap-ass gun from hobbytron, so i'll just take the part from that. :)
  • 0

Yea, as I walk through the shadow of the Valley of Death, I shall not fear because I am the baddest motherfucker in the Valley.

AxelTheWicked
Private
Private
 
Posts: 10
Joined: Sun Aug 16, 2009 5:43 am
Location: Santa Clara, California
Country: United States (us)
Reputation: 0

Unread postAuthor: irisher » Sat Jul 24, 2010 12:04 am

i alredy went ahead and ordered a cheap-ass gun from hobbytron
Just a word of advice. Don't do business with them. It took me over a year to get a refund for a defective product and IIRC they are being sued for bad business practices.
  • 0

User avatar
irisher
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 420
Joined: Mon Dec 29, 2008 2:53 am
Reputation: 0

Sponsored

Sponsor
 


Unread postAuthor: AxelTheWicked » Sat Jul 24, 2010 12:47 am

lol! i don't care if the product is defective. i just need a spare part from the gun i ordered. that's the only reason i'm getting it, cuz it's a cheap gun that i'm not gonna use. (i bought my airsoft pistol from a store called Armorgeddon. cost me about $30.)
  • 0

Yea, as I walk through the shadow of the Valley of Death, I shall not fear because I am the baddest motherfucker in the Valley.

AxelTheWicked
Private
Private
 
Posts: 10
Joined: Sun Aug 16, 2009 5:43 am
Location: Santa Clara, California
Country: United States (us)
Reputation: 0

Return to BB/Airsoft/Pellet Gun Discussion

Who is online

Registered users: Bing [Bot], Google [Bot], Yahoo [Bot]

Reputation System ©'