| Author |
Message
|
| D_Hall |
 Posted: 04/30/2008 23:15 PM Post subject: Fuel Injection and Air Mixing.... |
 |
|
Donating Member
Joined: 07 Feb 2008
Posts: 459
1085.45 Spud Bux
|
Just thought I'd bounce an idea off ya'll. I'm pretty sure it's a sound idea, but still, a fresh pair of eyes never hurts.
OK, proper fuel/air mixing is required for good combustion. Around here that's often done with chamber fans. I'm not saying chamber fans are bad or that I won't use 'em. I'm wondering, however, if their job would be made MUCH easier if an eductor was used.
More to the point, I was thinking: McMaster part num: 5205K24
Feed it propane and air (as appropriate to which step of fueling you're in) and it ought to pull in fuel/air from the chamber to really help the mixing.
Thoughts? |
|
| Back to top |
|
 |
|
|
|
| bigbob12345 |
| Posted: 04/30/2008 23:21 PM Post subject: |
|
|
Experienced n00b
Joined: 01 Dec 2007
Posts: 1514
362.74 Spud Bux
|
Umm good idea but it is very expensive
$45, you could buy like 5 chamber fans with that which would proabably give more flow then this air flow booster.
But if I had the money Id be willing to try it, its an intresting idea. |
|
| Back to top |
|
|
| BigGrib |
| Posted: 04/30/2008 23:25 PM Post subject: |
|
|
GribNation Founder
Joined: 01 Oct 2007
Posts: 611
176.25 Spud Bux
|
| i'm not really sure how that thing works, but from the looks of it you'd have to drill a bigger hole in the chamber or something, and you'd still have to meter it exactly as if you have a chamber fan in it. from the looks if it, it only mixes the fuel and would still have the propane sit in one spot instead of distributing the fuel/air mixture evenly throughout the chamber. but like i said i really dont know how that thing works, i'm just guessing here. If you could explain it to me i'd appreciate it. |
|
| Back to top |
|
|
| starman |
| Posted: 04/30/2008 23:43 PM Post subject: |
|
|
Big Daddio
Joined: 12 Dec 2007
Posts: 824
1255.86 Spud Bux
|
I'm not familiar with these things and even studying over them some not sure how or why they work. Low cfm boosted to high cfm through use of another compressed air input.
Can you elaborate some on how they might be utilized in chamber mixing? |
|
| Back to top |
|
|
| D_Hall |
| Posted: 04/30/2008 23:50 PM Post subject: |
|
|
Donating Member
Joined: 07 Feb 2008
Posts: 459
1085.45 Spud Bux
|
Basically they're tuned eductors/ejectors (same gizmo, different names).
Link to Wikipedia article
Using the above sketch (hope that pic links well).... As I would envision thier use in a hybrid, the motive fluid would the fuel being injected(*). The inlet gas would be the air inside the chamber (yes, the whole thing is inside the chamber). This would mix fuel with air in a very efficient manner while moving large quanitities of air around within the chamber.
(*) And later the supplimental air, but for now we'll just talk about fuel. |
|
| Back to top |
|
|
| D_Hall |
| Posted: 04/30/2008 23:55 PM Post subject: |
|
|
Donating Member
Joined: 07 Feb 2008
Posts: 459
1085.45 Spud Bux
|
| bigbob12345 wrote: | Umm good idea but it is very expensive
$45, you could buy like 5 chamber fans with that which would proabably give more flow then this air flow booster. |
The one I quoted moves 26.4 cfm; about the same as an 80 mm cooling fan (which tend to go for about $20). The big advantages....
1) It's virtually indestructible.
2) It's inherently safe. No amount of damage to it would ever result in frayed wires or anything that could ever be a safety hazard.
Disadvantage....
1) Once the fuel/air is injected, the mixing is done. You can't just let it run for 20 minutes. |
|
| Back to top |
|
|
| BigGrib |
| Posted: 04/30/2008 23:58 PM Post subject: |
|
|
GribNation Founder
Joined: 01 Oct 2007
Posts: 611
176.25 Spud Bux
|
| how would you meter everything with that setup or do you know yet |
|
| Back to top |
|
|
| THUNDERLORD |
| Posted: 05/01/2008 0:05 AM Post subject: |
|
|
Colonel
Joined: 28 Mar 2008
Posts: 551
1879.93 Spud Bux
|
Looks sort of like it will only circulate by the "motive fluid" so if the mix was off it would still need to be vented out manually.
Unless it is very precise. But I'm not familiar with the part.
The carburation or fuel injection is interesting though. |
|
| Back to top |
|
|
| D_Hall |
| Posted: 05/01/2008 0:21 AM Post subject: |
|
|
Donating Member
Joined: 07 Feb 2008
Posts: 459
1085.45 Spud Bux
|
| BigGrib wrote: | | how would you meter everything with that setup or do you know yet |
A metering pipe, just like everybody else. The only difference would be that inside the chamber at the fuel injection point you'd find the ejector. The ejector would not affect overall fuel/air mixture one iota. What it WOULD do is aid in mixing fuel/air in the chamber. |
|
| Back to top |
|
|
| BigGrib |
| Posted: 05/01/2008 0:24 AM Post subject: |
|
|
GribNation Founder
Joined: 01 Oct 2007
Posts: 611
176.25 Spud Bux
|
| well from looking at it and thinking about it, you could definitely use this to mix the fuel/air but i would still recommend the use of a chamber fan to disperse the fuel throughout the chamber and to blow spent gases from the chamber after firing. |
|
| Back to top |
|
|
| Lentamentalisk |
| Posted: 05/01/2008 0:53 AM Post subject: |
|
|
Resident Tinkerer
Joined: 07 Aug 2007
Posts: 614
209.68 Spud Bux
|
| BigGrib has a point... This thing helps with mixing the fuel, but doesn't do a thing for venting the chamber afterwards, though it is quite an attractive idea. I'm very interested to see how this can be used. |
|
| Back to top |
|
|
| Hotwired |
| Posted: 05/01/2008 9:31 AM Post subject: |
|
|
UK Spudgunner
Joined: 13 Oct 2006
Posts: 1545
3163.94 Spud Bux
|
The solid eductor would certainly be more robust than the average chamber fan.
I can't see a $40 bit of metal making much of a dent in a five figure budget so cost isn't important.
I actually thought you were going to be injecting them together but after reading through more carefully you're looking to separate the two.
Why not have them simultaneously mixed in a carburettor style with an air jet pulling in the fuel from a restricted orifice? |
|
| Back to top |
|
|
| Lentamentalisk |
| Posted: 05/01/2008 9:52 AM Post subject: |
|
|
Resident Tinkerer
Joined: 07 Aug 2007
Posts: 614
209.68 Spud Bux
|
| Hotwired wrote: | | Why not have them simultaneously mixed in a carburettor style with an air jet pulling in the fuel from a restricted orifice? |
What ever fuel is used (unless it is gasoline... Yikes!) it is already going to be under pressure, so that won't exactly work as far as I can see, unless you had some pressure release valve that was triggered by the slight vacuum.
The real issue is that the thing can't push much pressure out at all, so it won't work for pressurizing the chamber.
However, if you stick it inside, then you can do a primary mixing when you add the fuel, and then another mixing by pumping the air through the same inlet as the propane. |
|
| Back to top |
|
|
| D_Hall |
| Posted: 05/01/2008 10:04 AM Post subject: |
|
|
Donating Member
Joined: 07 Feb 2008
Posts: 459
1085.45 Spud Bux
|
| Lentamentalisk wrote: | | However, if you stick it inside, then you can do a primary mixing when you add the fuel, and then another mixing by pumping the air through the same inlet as the propane. |
This is indeed the plan.
As for venting afterwards.... Originally I was planning on pulling a vacuum on the chamber. EXCELLENT purging! After running numbers and such, I realized that I'd save a lot of money and get pretty good results simply by using a couple of 5 HP shop vacs for 30 minutes(*).
(*) Put a 2" ball valve on each chamber leg. Attach hose. Pull air through barre/chamber. Shop vacs (combined) should move 240 cfm. Chamber is 170 cf. Run 'em for 30 minutes and I should be down to negligable remnant combustion gases. |
|
| Back to top |
|
|
| jimmy101 |
| Posted: 05/01/2008 12:38 PM Post subject: |
|
|
Major General
Joined: 28 Mar 2007
Posts: 1415
5996.50 Spud Bux
|
Basically, you're talking about a mixing manifold or carburator. The tricky part is getting the mix correct. In a true mixing mainifold you would regulate the pressure of both gases. Pretty darn tricky for propane + air since one is 25x the volume of the other. Small errors in pressure will kill the accuracy of the mix.
I think the eductor will have the same kind of problem as a mixing manifold. How to precisely control the air / propane ratio. Are you thinking of having the eductor injest say all the propane plus half the air to get good mixing then "topping off" the chamber with the rest of the air?
How bout this instead...
1. Evacuate the chamber down to a moderate vacuum, perhaps 0.1 ATM.
2. Pressurize the chamber with propane to your target propane mole fraction + whatever the vacuum was. So, for a 10X mixture, and if the vacuum was 0.1 ATM (1.5 PSIA), you pressurize with propane to 5.9 + 1.5 = 7.4 PSIA. I would think the combination of the low initial pressure in the chamber and the high inlet flow would equilibrate the propane thoughout the chamber pretty quickly.
3. Now inject air at high pressure until the chamber reaches the desired final pressure. The air could be injected simultaneously from several ports.
I believe this is similar to what you posted before. The difference is the order of injecting the gases. Instead of injection 4% of the chamber volume in propane at high pressure you would inject 96% of the chamber volume in air at high pressure. Should give much better mixing. |
|
| Back to top |
|
|
|
|
