| Author |
Message
|
| Infernal2 |
 Posted: 09/11/2006 21:44 PM Post subject: High Pressure Materials for Pistons |
 |
|
Staff Sergeant
Joined: 11 Sep 2006
Posts: 122
274.15 Spud Bux
|
I'm wondering if there is a possibility of using a high pressure rated material for the formation of pistons. I don't have much access to a lathe but I have a rather large selection as far as anything from steel, concrete, wood, and rubber for casting. I imagine the obvious materials as steel and rubber would be excellent but casting density materials are expensive.
A high density wood would be brittle but a hydraulic concrete would (in theory) provide an excellent pistoning material. Has anyonne tried a resin or concrete piston? |
|
| Back to top |
|
 |
|
|
|
| ProfessorAmadeus |
| Posted: 09/11/2006 22:00 PM Post subject: |
|
|
Running with Scissors
Joined: 28 Apr 2006
Posts: 1046
280.78 Spud Bux
|
| Use an endcap that fits in either the tee or if its a coaxile in the pipe. And a good bumper and a sealing face and your done. |
|
| Back to top |
|
|
| rna_duelers |
| Posted: 09/12/2006 1:37 AM Post subject: |
|
|
Major General
Joined: 26 Sep 2005
Posts: 1641
3118.23 Spud Bux
|
| Concrete sounds very heavy,the lighter the piston faster it open and thus better performance a good trick is to get a crap load of hot glue gun sticks and melt them in an old frying pan and mould a piston from that it is said ot work very well. and u can also hollow the inside a little,not a lot but a little to make it even lighter. |
|
| Back to top |
|
|
| MrCrowley |
| Posted: 09/12/2006 2:39 AM Post subject: |
|
|
Blizzard of Ozz
Joined: 23 Jun 2006
Posts: 5950
2661.09 Spud Bux
|
oh,no not the glue melting thing,i tried that lol and the non-stick stuff caught on fire so i turned the element(heating thingy)off and the glue dried really fast and the pot...well lets just say the pot got phucked.its all black and has a gluey coating on the inside.  my piston is made from a pringles sleeved in 3" dwv pipe filled with some blue foam stuff, i made a post about it last night......http://www.spudfiles.com/forums/viewtopic.php?t=3609& |
|
| Back to top |
|
|
| Infernal2 |
| Posted: 09/14/2006 21:25 PM Post subject: |
|
|
Staff Sergeant
Joined: 11 Sep 2006
Posts: 122
274.15 Spud Bux
|
Well, I'll post pictures as soon as I get done shaping. I used a three inch pipe and a mixture of Sonoguard 55W, Emaco P24 Hardener (PT 2), and a siliconzied rubber caulking. These materials took a little experimentation but appear to take the properties of a non-flaking semi-rigid caulking. I'm letting them cure for four days to insure total cure.
The Sonogaurd 55W should provide an oilly surface so lubrication may not be needed on the piston. According to weight estimates the inch and a quarter piston should weigh about 15 grams.
I'll let you know... |
|
| Back to top |
|
|
| Infernal2 |
| Posted: 09/17/2006 12:06 PM Post subject: |
|
|
Staff Sergeant
Joined: 11 Sep 2006
Posts: 122
274.15 Spud Bux
|
Ok, well, the combo didn't work. However, I did find an excellent material for pistons. Dow Corning makes a coloured silicon caulk (451) that makes an awesome piston. As long as you let it cure for the appropriate time then you can make a solid piston without using neoprene or rubber. AT least, it works for me.
I set the caulk in a three inch tube of sch 40 and suspended a compression spring in the top of the pour. After this set for 48 hours (pressure should also be rising, as with any caulk) I removed the tube, peeled back the caulk ( I use form board with form oil as a bottom for my mould), and voila, spring and piston. I then drilled a hole for my washer and backed the whole thing with galvanized pipe cap. |
|
| Back to top |
|
|
| POS |
| Posted: 09/17/2006 13:23 PM Post subject: |
|
|
Major
Joined: 14 Sep 2006
Posts: 395
264.52 Spud Bux
|
| Nice doing. Could you post a picture of that piston ? |
|
| Back to top |
|
|
| Infernal2 |
| Posted: 09/20/2006 20:26 PM Post subject: |
|
|
Staff Sergeant
Joined: 11 Sep 2006
Posts: 122
274.15 Spud Bux
|
| I'd love to but alas, it too did not work.... Good for one use only...LOL |
|
| Back to top |
|
|
|
|
