| Author |
Message
|
| imjustpk |
 Posted: 04/14/2007 23:00 PM Post subject: |
 |
|
Corporal
Joined: 28 Jan 2007
Posts: 63
145.44 Spud Bux
|
| Oh ok, that makes sense. Thanks for the info, I’ll probably give this a try when I get some rubber for it. |
|
| Back to top |
|
 |
|
|
|
| AmYisroelChai |
| Posted: 04/25/2007 13:12 PM Post subject: |
|
|
Staff Sergeant
Joined: 29 Mar 2007
Posts: 122
350.68 Spud Bux
|
| noname wrote: | Filing the rod down increases airflow a bit, drilling the holes out makes it even better. The rubber disc is so that it can actually move, and it seals.
Most sprinkler valves are barrel sealers, I haven't seen any that aren't. |
This looks great. If I do this to a Husky Blow Gun will it vent fast enough to port a 3" or 4" coaxial? What about a 2" Piston?
Second question, you mentioend tha you drilled holes as in plural. But the pic shows one hole on the removabel inside whats the second hole tat gets drilled.
Third, sorry what part of the internal rod do you file? The middle part between the O-rings.
Thank you in advance. |
|
| Back to top |
|
|
| noname |
| Posted: 04/25/2007 16:35 PM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
1st, you can try, but I still doubt it. It may be able to pilot a 2" valve, but it'll be slow. A modified blowgun has about the same flow as a 1/4" ball valve.
2nd: There's a hole on each side of the tube holding the rod, drill them both.
3rd: Yes, the part between the O-rings. I would highly recommend putting some masking tape or something over the O-rings to protect them; it's very easy to damage them and ruin the seal. |
|
| Back to top |
|
|
| AmYisroelChai |
| Posted: 04/25/2007 16:42 PM Post subject: |
|
|
Staff Sergeant
Joined: 29 Mar 2007
Posts: 122
350.68 Spud Bux
|
Thank you no name.
Also to mod the inside diaphragm...Am i looking for something that fits in the hole, or something that fits in the spring? I guess I am asking is when the air is released the piston flies up, what’s to make sure t doesn’t go awry and move away from under the spring and go to the side and thereby prevent a good seal from happening? |
|
| Back to top |
|
|
| noname |
| Posted: 04/25/2007 16:45 PM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
| I cut a sheet rubber circle to size, then epoxied a Fun Quest token to it. It fits perfectly inside the spring. |
|
| Back to top |
|
|
| AmYisroelChai |
| Posted: 04/25/2007 16:51 PM Post subject: |
|
|
Staff Sergeant
Joined: 29 Mar 2007
Posts: 122
350.68 Spud Bux
|
If I am in doubt as to an exact fit. should i hot glue the "piston" to the spring.
I was going to go to home Depot and find the right sized washer at the same time is searched for the O-Ring |
|
| Back to top |
|
|
| noname |
| Posted: 04/26/2007 20:04 PM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
| You can if you want, just try your ideas and see if they work. |
|
| Back to top |
|
|
| Kenny_McCormic |
| Posted: 04/30/2007 19:27 PM Post subject: |
|
|
1st Lieutenant
Joined: 03 Jan 2007
Posts: 281
265.61 Spud Bux
|
| when drilling the blowgun be sure to drill out the holes in the blowgun body itself for even better flow |
|
| Back to top |
|
|
| noname |
| Posted: 04/30/2007 20:59 PM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
| That gets complicated, my camera's battery died while writing the How-To, so I just left that out. It isn't needed though, because the flow is choked by the internals, and not very much by the body itself. |
|
| Back to top |
|
|
| rhyco |
| Posted: 05/02/2007 4:40 AM Post subject: |
|
|
Private
Joined: 19 May 2006
Posts: 11
14.76 Spud Bux
|
| is that a Australian 2 dollar coin? |
|
| Back to top |
|
|
| noname |
| Posted: 05/02/2007 18:30 PM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
|
| Back to top |
|
|
| LikimysCrotchus5 |
| Posted: 09/22/2007 23:42 PM Post subject: |
|
|
Brigadier General
Joined: 04 Sep 2007
Posts: 838
1953.45 Spud Bux
|
i got a question. Ho do you reduce the size of the internals to half of what they were. by compressing them or with a nail file or whatever?
And you drill that hole to make it 1/4 inch for the blowgun valve right? |
|
| Back to top |
|
|
| noname |
| Posted: 09/23/2007 10:14 AM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
| Try rewording your questions, I couldn't really understand either of them. In the second one, are you asking how big of a hole to drill? |
|
| Back to top |
|
|
| VH_man |
| Posted: 10/08/2007 19:54 PM Post subject: |
|
|
Airsoft Freak
Joined: 09 Dec 2006
Posts: 1067
1273.73 Spud Bux
|
| i tried what you are doing and i cant get enough air to exit so that the valve actuates.......... |
|
| Back to top |
|
|
| noname |
| Posted: 10/09/2007 20:37 PM Post subject: |
|
|
Mr Vortex
Joined: 10 Apr 2006
Posts: 2509
2698.56 Spud Bux
|
"Get enough air to exit."
Pilot volume or something?
It could also be how you made the diaphragm and modified the blowgun. Don't expect your first homemade diaphragm valve to work, especially since almost no one makes them. It seems to be all pistons nowadays.  |
|
| Back to top |
|
|
|
|
