| Cool Eh? |
| Yeah WOOOOOO! |
|
50% |
[ 7 ] |
| This sucks |
|
7% |
[ 1 ] |
| I am making one straight away! |
|
42% |
[ 6 ] |
|
| Total Votes : 14 |
|
| Author |
Message
|
| Insomniac |
 Posted: 12/18/2006 21:03 PM Post subject: Incredible Paper Dart |
 |
|
Colonel
Joined: 18 Dec 2006
Posts: 692
133.92 Spud Bux
|
Hi everybody, I've been browsing theses forums for some time but my Dad wouldn't let me sign up. He changed his mind yesterday though, so I am writing this simple How-To on my favourite type of ammo. This dart is good as its so lightweight it's safe for suburban areas, it's cheap and most important of all it flys exeptionally well. With my simple ball valve pnumatic, I can send one of these out of sight straight up. If built well they fly perfectly straight, if built badly you may as well shoot cotton wool.
These are NOT my design, I found them on this site http://tomshiro.org/pdart/ but his method of making them is fairly complicated compared to mine.
1. Get a sheet of MAGAZINE paper.
2. With the paper in portrait orientation, start to roll an EXTREMELY NARROW cone from the corner.
3. Keep rolling, doing your best to keep it tight, narrow and sharp.
4. When there is only a small triangle left to roll, stop rolling and lick the triangle. (Glue could also be used )
5. Finish rolling the dart, and lick the spiral seam from the point to the tail. You really need to get it wet or it wont stick.
6. lick the tip of the dart and roll it between you fingers to seal the small hole on the tip.
7. Slide it into your barrel, and get some scisssors to cut the excess off.
8. BEFORE YOU CUT slide the dart out of the barrel slightly, otherwise the tail will be crushed when you cut.
9. Have fun 
Please give feedback, this is my first how to and I want to know what you think.
I just had an idea. Seeing as my gun is a ball valve gun, the darts can usually make it out the barrel in one piece. For more powerful guns, you may need to either lower the pressure, glue the dart or cover it in electrical tape.
The pictures are in reverse order, Whoops!
| Description: |
|
| Filesize: |
25.57 KB |
| Viewed: |
70 Time(s) |
|
| Description: |
| Move the dart out of the barrel slightly before cutting |
|
| Filesize: |
34.09 KB |
| Viewed: |
63 Time(s) |
|
| Description: |
|
| Filesize: |
22.86 KB |
| Viewed: |
70 Time(s) |
|
| Description: |
| Wet the end and then roll it between your fingertips |
|
| Filesize: |
24.11 KB |
| Viewed: |
65 Time(s) |
|
| Description: |
| Lick the triangle then continue rolling |
|
| Filesize: |
29.92 KB |
| Viewed: |
89 Time(s) |
|
| Description: |
|
| Filesize: |
32.86 KB |
| Viewed: |
80 Time(s) |
|
| Description: |
| Make sure the dart is very narrow |
|
| Filesize: |
31.19 KB |
| Viewed: |
51 Time(s) |
|
Last edited by Insomniac on 12/18/2006 21:22 PM; edited 1 time in total |
|
| Back to top |
|
 |
|
|
|
| Bluetooth |
| Posted: 12/18/2006 21:11 PM Post subject: |
|
|
Brigadier General
Joined: 27 Jun 2006
Posts: 828
34.79 Spud Bux
|
| That is amazingly cool, simple aaaaaaaaand most of all CHEAP!!!! Thnx for posting it .
|
|
| Back to top |
|
|
| Insomniac |
| Posted: 12/18/2006 21:24 PM Post subject: |
|
|
Colonel
Joined: 18 Dec 2006
Posts: 692
133.92 Spud Bux
|
| Your welcome. If you build one, post you results here. I'm interested to see what happens when they are fired from more powerful guns.
|
|
| Back to top |
|
|
| Bluetooth |
| Posted: 12/18/2006 21:35 PM Post subject: |
|
|
Brigadier General
Joined: 27 Jun 2006
Posts: 828
34.79 Spud Bux
|
| I made one but its 9:00 here and pitch black out. Ill post the results tomarrow.
|
|
| Back to top |
|
|
| pyromanic13 |
| Posted: 12/18/2006 21:40 PM Post subject: |
|
|
Brigadier General
Joined: 19 Oct 2005
Posts: 912
0.11 Spud Bux
|
| i've made em before and they're really fun. try putting needles on the tip. also try shooting them out of a paintball gun.
|
|
| Back to top |
|
|
| ProfessorAmadeus |
| Posted: 12/18/2006 21:42 PM Post subject: |
|
|
Running with Scissors
Joined: 28 Apr 2006
Posts: 1046
280.78 Spud Bux
|
| Put a large roofing nail in it so that it has a heavy tip. Thats my main damage ammo.
|
|
| Back to top |
|
|
| Insomniac |
| Posted: 12/18/2006 21:44 PM Post subject: |
|
|
Colonel
Joined: 18 Dec 2006
Posts: 692
133.92 Spud Bux
|
If you built the dart well you may as well shoot it at night. They go so damn fast you'll be lucky to see it at all.
I shot the one in the pics. It didn't go too well, it was a bit unstable, and turned sideways a few times. I still lost sight of it though.
Also, if you put somthing like a twig on the tip, you can put one of those red caps from cap guns on them. That way it goes POP! when it hits the ground, making it easier to measure the amout of time between launch and impact with the ground. I suppose that you could use some mathmatical formula to work out how high it went if you knew the hang time, but I'll leave that to somone who knows more math than me. I'm 13 and we haven't covered advanced projectile motion in maths. lol 
Last edited by Insomniac on 12/19/2006 2:13 AM; edited 2 times in total |
|
| Back to top |
|
|
| pyromanic13 |
| Posted: 12/18/2006 21:50 PM Post subject: |
|
|
Brigadier General
Joined: 19 Oct 2005
Posts: 912
0.11 Spud Bux
|
some kid from holland once told me me used to go hunting with these 
|
|
| Back to top |
|
|
| Insomniac |
| Posted: 12/18/2006 21:51 PM Post subject: |
|
|
Colonel
Joined: 18 Dec 2006
Posts: 692
133.92 Spud Bux
|
Yeah, but i doubt a paper dart could do much unless it was tipped with a nail or somthing.....unless it got you in the eye 
|
|
| Back to top |
|
|
| MrCrowley |
| Posted: 12/18/2006 21:55 PM Post subject: |
|
|
Blizzard of Ozz
Joined: 23 Jun 2006
Posts: 5950
2661.09 Spud Bux
|
| You can aslo make darts using the tips from caulking tubes, and you can put drill bits or nails in the tips and they're my number one damage ammo.(check my sig for pics under paintball rifle)
|
|
| Back to top |
|
|
| Bluetooth |
| Posted: 12/18/2006 21:57 PM Post subject: |
|
|
Brigadier General
Joined: 27 Jun 2006
Posts: 828
34.79 Spud Bux
|
| Its like " I made mine out of microscopicly think titainium sheet."
|
|
| Back to top |
|
|
| Insomniac |
| Posted: 12/18/2006 22:00 PM Post subject: |
|
|
Colonel
Joined: 18 Dec 2006
Posts: 692
133.92 Spud Bux
|
Yeah, the caulking tube ones would be better, but the whole point of these darts isn't damage, it's the fact that they fit any small bore guns, shoot real far and are CHEAP CHEAP CHEAP
If we had more room I would tip them with nails, but I live in the middle of a city, and I can shoot these straight up without worrying about what it hits on the way down.
@Mr Crowley, I saw the pictures and all i can say is WOW! I would try with my gun but it uses a ball valve, making it damn near impossible to aim.
|
|
| Back to top |
|
|
| MrCrowley |
| Posted: 12/19/2006 2:44 AM Post subject: |
|
|
Blizzard of Ozz
Joined: 23 Jun 2006
Posts: 5950
2661.09 Spud Bux
|
|
| Back to top |
|
|
| Insomniac |
| Posted: 12/19/2006 3:35 AM Post subject: |
|
|
Colonel
Joined: 18 Dec 2006
Posts: 692
133.92 Spud Bux
|
| Heheheheh great idea. I had already heard of using a spring, I will have to try it. Does it need to be a big spring or will most tension springs work?
|
|
| Back to top |
|
|
| MrCrowley |
| Posted: 12/19/2006 3:55 AM Post subject: |
|
|
Blizzard of Ozz
Joined: 23 Jun 2006
Posts: 5950
2661.09 Spud Bux
|
| well just ask for a high-compression spring at your local hardware store. It needs to be-able to expand without too mcuh strength or disfiguring the spring and making it longer.
|
|
| Back to top |
|
|
|
|
