| Author |
Message
|
| spudling |
 Posted: 08/13/2007 19:53 PM Post subject: paintball mini combustion |
 |
|
Specialist
Joined: 27 Oct 2006
Posts: 48
0.36 Spud Bux
|
| ok im going paintballing this saturday (13th) and i wan t make an under barrel launcher for my tipmann 98 so it needs to be small but powerfull so i need some ideas i was thinking of one of those pocket cannons |
|
| Back to top |
|
 |
|
|
|
| homedepotpro |
| Posted: 08/13/2007 20:20 PM Post subject: |
|
|
Lieutenant Colonel
Joined: 26 Nov 2006
Posts: 446
450.72 Spud Bux
|
sounds good. isn't Saturday the 18th. have you every build a co2 regulated pneumatic gun before. im asking because you posted in the wrong section, which means you're new the the web site and probably spud gunning. this seem like quite an ambitious project to put off in a week
edit: my bad, i heard paintball and assumed pneumatic.
Last edited by homedepotpro on 08/13/2007 21:31 PM; edited 1 time in total |
|
| Back to top |
|
|
| spudling |
| Posted: 08/13/2007 21:03 PM Post subject: |
|
|
Specialist
Joined: 27 Oct 2006
Posts: 48
0.36 Spud Bux
|
| yes i only make pneumatic guns this will be my first combustion |
|
| Back to top |
|
|
| jackssmirkingrevenge |
| Posted: 08/13/2007 21:07 PM Post subject: |
|
|
space monkey
Joined: 15 Mar 2007
Posts: 7050
11306.91 Spud Bux
|
you'll need some sort of preloaded cartridge, I can't see you spraying deoderant into your chamber in the middle of a paintball game  |
|
| Back to top |
|
|
| homedepotpro |
| Posted: 08/13/2007 21:35 PM Post subject: |
|
|
Lieutenant Colonel
Joined: 26 Nov 2006
Posts: 446
450.72 Spud Bux
|
| i don't think this will work in time. for what you describing, it sounds like you'll need to use meter propane or MAPP gas. the smaller you go the harder it is to get consistent shot because its harder to get the right fuel to air mix. the only thing i think that comes close would be this http://www.burntlatke.com/mini.html |
|
| Back to top |
|
|
| thespeedycicada |
| Posted: 08/13/2007 21:42 PM Post subject: |
|
|
Lieutenant Colonel
Joined: 12 Aug 2007
Posts: 435
528.45 Spud Bux
|
| for a single shot put some flour in the chamber shake it up and ignite!No need to spray in fuel. |
|
| Back to top |
|
|
| Spudinator |
| Posted: 08/14/2007 0:03 AM Post subject: |
|
|
Donating Member
Joined: 13 Feb 2005
Posts: 56
244.09 Spud Bux
|
Dude, Flour? WTF?
Get a small propane torch, give the inside of the chamber a couple seconds from that and its all good. The torch pre-mixes the correct amount of fuel into the air (the holes at the base of the torch, thats the air intake). I made a pill-bottle (albeit a monster pill bottle lol) paintball combustion that could throw a paintball at 400 fps, though it was 3' long...
Perhaps coax would be your best bet for something like this, use 1.5" or 2" PVC with a 3/4" CPVC barrel (.69 ID  ). |
|
| Back to top |
|
|
| jackssmirkingrevenge |
| Posted: 08/14/2007 0:24 AM Post subject: |
|
|
space monkey
Joined: 15 Mar 2007
Posts: 7050
11306.91 Spud Bux
|
| What you want to be practical in a game of paintball is probably something like my combustion cartridge, a unit that will take simple pre-filled cylinders with gas and ammunition - incidentally, what are you planning for the latter? Presumably a whole bunch of paintballs, so at least 1" caliber... |
|
| Back to top |
|
|
| spudling |
| Posted: 08/16/2007 7:43 AM Post subject: |
|
|
Specialist
Joined: 27 Oct 2006
Posts: 48
0.36 Spud Bux
|
| another thing is it needs to stay around 270 fps as a rule |
|
| Back to top |
|
|
| spud yeti |
| Posted: 08/16/2007 9:46 AM Post subject: |
|
|
can i change this name
Joined: 08 May 2007
Posts: 1043
14.05 Spud Bux
|
| With a combustion cannon its really hard to regulate speeds (unlike pneumatic) so perhaps sticking to pneumatics is more beneficial for this. If you build a pneumatic, it only needs about 50PSI to launch a paintball at 300fps. Therefore an onboard pump could work. I would make a piston valve too. |
|
| Back to top |
|
|
| spudling |
| Posted: 08/16/2007 10:44 AM Post subject: |
|
|
Specialist
Joined: 27 Oct 2006
Posts: 48
0.36 Spud Bux
|
i can do that but it needs to be small max 5" long
Last edited by spudling on 08/16/2007 11:13 AM; edited 1 time in total |
|
| Back to top |
|
|
| spud yeti |
| Posted: 08/16/2007 11:08 AM Post subject: |
|
|
can i change this name
Joined: 08 May 2007
Posts: 1043
14.05 Spud Bux
|
| Go for a coaxial. 3" chamber and 3/4" barrel. That would be your best, compact choice. |
|
| Back to top |
|
|
| frankrede |
| Posted: 08/16/2007 11:14 AM Post subject: |
|
|
Sangheili
Joined: 20 Jul 2006
Posts: 3046
618.25 Spud Bux
|
| A coaxial would work perfect then. |
|
| Back to top |
|
|
|
|
