Login    Register
User Information
Username:
Password:
We are a free and open
community, all are welcome.
Click here to Register
Sponsored
Who is online

In total there are 68 users online :: 3 registered, 0 hidden and 65 guests


Most users ever online was 155 on Mon Aug 15, 2016 1:40 am

Registered users: Bing [Bot], MSNbot Media, Yahoo [Bot] based on users active over the past 5 minutes

The Team
Administrators
Global Moderators
global_moderators.png CS

Airsoft Sniper

Post questions and info about pneumatic (compressed gas) powered cannons here. This includes discussion about valves, pipe types, compressors, alternate gas setups, and anything else relevant.
Sponsored 
  • Author
    Message

Unread postAuthor: spudthug » Sun Jun 17, 2007 5:26 pm

what do u mean? put a tiny orning on the inside of my barrel???
  • 0

4" piston valved cannon-half done..( i spilt my cement...)

Hybrid- 75% done. need to build propane holder and drill/tap sparkplug hole..
User avatar
spudthug
Brigadier General
Brigadier General
 
Posts: 936
Joined: Mon Feb 26, 2007 9:02 pm
Location: johnsonburg, Pa USA
Reputation: 0

Unread postAuthor: VH_man » Sun Jun 17, 2007 7:55 pm

no, right at the end. honestly, just dent it a little bit. either that or superglue/epoxy a peice of magnet wire to the back. its like .02 mm wide, and it can (amazingly) take the grunt of 150 PSI smashing into it. probobly better for your barrel than denting it.........
  • 0

User avatar
VH_man
Major General
Major General
 
Posts: 1827
Joined: Sat Dec 09, 2006 6:00 pm
Location: New Hampshire
Reputation: 1

Unread postAuthor: spudthug » Sun Jun 17, 2007 8:03 pm

magnet wire?? oh and i already found a way to stop it like 2 hours ago..i took a pair of plyers and squeezed at the end of my barrel a little..
  • 0

4" piston valved cannon-half done..( i spilt my cement...)

Hybrid- 75% done. need to build propane holder and drill/tap sparkplug hole..
User avatar
spudthug
Brigadier General
Brigadier General
 
Posts: 936
Joined: Mon Feb 26, 2007 9:02 pm
Location: johnsonburg, Pa USA
Reputation: 0

Unread postAuthor: VH_man » Mon Jun 18, 2007 6:04 am

well that works too........ lol.........
  • 0

User avatar
VH_man
Major General
Major General
 
Posts: 1827
Joined: Sat Dec 09, 2006 6:00 pm
Location: New Hampshire
Reputation: 1

Unread postAuthor: spudthug » Mon Jun 18, 2007 8:01 am

yea it works great and you cant even tell its there..not even from up close.. the only way you can see it is if you loook down the barrel...

it just stops the bb and i mean just stops it.. you could for it through if u wanted to but this works really good and i ddidnt have t odo anything to make my barrel crappy
  • 0

4" piston valved cannon-half done..( i spilt my cement...)

Hybrid- 75% done. need to build propane holder and drill/tap sparkplug hole..
User avatar
spudthug
Brigadier General
Brigadier General
 
Posts: 936
Joined: Mon Feb 26, 2007 9:02 pm
Location: johnsonburg, Pa USA
Reputation: 0

Unread postAuthor: ammosmoke » Sun Jun 24, 2007 2:40 pm

I meant at the beginning of the barrel, but whatever......

I meant that you should glue an o-ring on the end of the barrel that has the same OD, but a slightly smaller ID. Sorry, that wasn't very clear.
  • 0

<img>http://www.speedtest.net/result/309559995.png</img>
User avatar
ammosmoke
Brigadier General
Brigadier General
 
Posts: 1011
Joined: Wed Sep 27, 2006 10:57 am
Reputation: 0

Previous

Return to Pneumatic Cannon Discussion

Who is online

Registered users: Bing [Bot], MSNbot Media, Yahoo [Bot]

Reputation System ©'