slow open valve? actually the valve should be a lot faster then most piston air guns, the only problem would be the dead space, but if made well i dont think it would be much of a problemwyz2285 wrote:Them I would suggest a detente to compensate the slow open valve.
Search found 511 matches
- Fri May 18, 2012 2:59 am
- Forum: Pneumatic Cannons
- Topic: challenge to everyone
- Replies: 10
- Views: 3224
- Thu May 17, 2012 4:51 pm
- Forum: Pneumatic Cannons
- Topic: challenge to everyone
- Replies: 10
- Views: 3224
You don't need the o-rings in front of the bb, you bolt will push the bb through it, if you want it to act as a detente, you will need another one to seal the bolt/barrel section if not air will leak from there(it will any way without a o-ring there, but with a detente you lose more). As there is t...
- Thu May 17, 2012 3:55 am
- Forum: Pneumatic Cannons
- Topic: challenge to everyone
- Replies: 10
- Views: 3224
- Tue May 15, 2012 7:42 am
- Forum: Pneumatic Cannons
- Topic: challenge to everyone
- Replies: 10
- Views: 3224
i didnt really think of that, although i think when i came up with this i was more aiming for something that didnt waist any air, aslo i was thinking it may have a quicker valve opening time, but now i think about it it may not be by much if any This seems similar to the GB semi . although with the ...
- Tue May 15, 2012 7:12 am
- Forum: Pneumatic Cannons
- Topic: challenge to everyone
- Replies: 10
- Views: 3224
challenge to everyone
hey everyone, dont really do much in the hobby anymore but i still think of ways to much air guns and stuff, had this idea and would love to see it made, but i dont have the time to do it myself
not a very detailed drawing but you should get the idea
what do you think?
not a very detailed drawing but you should get the idea
what do you think?
- Sun Mar 04, 2012 8:19 pm
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
Did you use a belt grinder on this? no i just used an angle grinder and a file, but i think a belt grinder would have made it a lot easier I don't know. It looks great, the craftsmanship is amazing on the handle too - but somehow it doesn't feel right . I would have gone for the lanyard handle. Jus...
- Sat Mar 03, 2012 8:39 pm
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
- Thu Jan 26, 2012 1:03 am
- Forum: Pneumatic Cannons
- Topic: 1/2" Aluminium Coax
- Replies: 29
- Views: 15523
these are my two coax aluminium airguns, http://www.spudfiles.com/forums/8mm-coaxial-t22505.html http://www.spudfiles.com/forums/cane-gun-t21924.html both of them use 400psi and they wouldnt even be capably of that accuracy, 150psi just isnt going to cut it, also if you have a tight enough piston yo...
- Tue Jan 17, 2012 7:48 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
- Mon Jan 16, 2012 8:45 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
- Mon Jan 09, 2012 7:39 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
cheers guys im not sure what that thing at the front is, there are some other smaller ones on there, i will try and sand them of but it will be hard I'd suggest you try polishing and bluing the blade otherwise it'll rust quickly. thanks, ill take a look into that looks like a crack, did you quench i...
- Sun Jan 08, 2012 12:40 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
ok so i finally heat treated it today, did go as good as i had hoped, my dad was strongly saying that i didn't need to wear gloves, guess what, flames burnt my hands a little and it didn't go in as evenly as i wanted, the blade is a little bent but other then that i think it worked heres a couple of...
- Thu Dec 15, 2011 9:10 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
- Thu Dec 15, 2011 7:46 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
well, for that kind of steel, 830c would be pretty much ideal, since its carbon steel. and same for annealing thanks, i think the file i made this knife out of probably didn't get to much hotter then that, the furnace had been heated to 1000c but had been turned off and opened a few times, but i pu...
- Thu Dec 15, 2011 7:05 am
- Forum: Off-Topic Hobbies
- Topic: file knife (in the making)
- Replies: 49
- Views: 13332
OIL, use oil!!! Cause if the nprmalizating process isnt exacly perfect, it will crack during the quench definitely think i will use the oil then, havent done this much to have it crack on me... can anyone tell me what the best annealing and heat treating temperatures are? JSR, i want to make a knif...