Page 2 of 2
Posted: Sun Jul 10, 2011 10:16 am
by Sch120PVC
Ok, I have Uploaded Some Damage Pics For U Guys to see the damage a Sch 80 Rifle Can Do......all Shots were at 200 psi! I have also build a metal cannon on recommendation of some of the spudfiles members earlier in this post so u can check that out too!
Posted: Sun Jul 10, 2011 10:24 am
by Sch120PVC
Ok, I have Uploaded Some Damage Pics For U Guys to see the damage a Sch 80 Rifle Can Do......all Shots were at 200 psi! I have also build a metal cannon on recommendation of some of the spudfiles members earlier in this post so u can check that out too!
My New Gun Which Is Made Of Galvanized Metal ....Tested to about 500 psi and it totally Hit me in the gut by the recoil! It Has A Volume Of 25 Cubic Inches!
The New Galvanized metal gun in comparison to my previous Sch 80 Pvc gun!
The Damage My Sch 80 Pvc rifle did to a 9Volt Battery....It tore right through all the Other Smaller Batteries inside....and the ammo was needle sharp before the shot!
Damage to a PVC Glue Can!
Sch 80 PVC Rifle vs PVC glue can at 200 psi! Velocity 922 fps (GGDT)
Posted: Sun Jul 10, 2011 11:59 am
by jackssmirkingrevenge
Good stuff
all you need now is a better valve
Posted: Sun Jul 10, 2011 1:56 pm
by Sch120PVC
Too right mate but the problem is sprinkler valves dont hold that high pressures while im too lazy to make a piston! But ill probably order a 500 psi sprinkler valve which i am getting off a local dealer!!! Cant wait for my new valve..... 500 PSI + Sprinkler Valve = Carnage xD
Posted: Sun Jul 10, 2011 1:59 pm
by jackssmirkingrevenge
Why not just get something like
this? It should happily take 500 psi without failure and will likely be more compact and efficient, as well as much cheaper.
Posted: Sun Jul 10, 2011 2:28 pm
by POLAND_SPUD
I have also build a metal cannon on recommendation of some of the spudfiles members earlier in this post so u can check that out too!
nice...
when you build a QEV gun and/or increase pressure used you can reduce the chamber volume considerably
metal fittings&pipes are not really that heavy you know - the thing is that ppl buy large diam pipes and fittings while a short 1" or 3/4" nipple will do just fine
Posted: Sun Jul 10, 2011 9:49 pm
by Sch120PVC
jackssmirkingrevenge wrote:Why not just get something like
this? It should happily take 500 psi without failure and will likely be more compact and efficient, as well as much cheaper.
i still havent decided which valve to use ....the qev definitely will do the job + its free shipping outside the US so i might consider that too ....thanx for the link!
And the new metal gun + 500 psi + ball valve is scary...cant imagine it with a quicker valve...now all i have to do is save up for a better valve!
Posted: Sun Jul 10, 2011 10:14 pm
by jackssmirkingrevenge
Sch120PVC wrote:...now all i have to do is save up for a better valve!
Save up for a $20 valve? Man I'm glad I'm not a student anymore
Posted: Sun Jul 10, 2011 10:17 pm
by Sch120PVC
jackssmirkingrevenge wrote:Sch120PVC wrote:...now all i have to do is save up for a better valve!
Save up for a $20 valve? Man I'm glad I'm not a student anymore
University? xD