Page 1 of 1

Great How to...working with copper pipe

Posted: Fri Feb 23, 2007 10:57 pm
by trae08
by no means am i claiming this as my own work i got this from http://www.osh.com/Cultures/en-US?ft=true i saved the images and just copied the hosting links in the right places.. i thought this was a great how to and thought everyone should read it or at least if you make or want to make a copper gun. so any and all apreciation should go to http://www.osh.com/Cultures/en-US?ft=true


again i copied this from the site above and am not claiming it as mine

edit: any smilies or anything is from there config of characters when the forum recognizes them its makes them a smilie there not from anything i put in there..

i also think this should be stickied but thats just me



((((( OSH provides the following How To information as a service to our visitors. Due to differing tools, individual skills, products, materials, building codes, local regulations and conditions, OSH assumes no responsibility for any damages, injuries, or losses incurred resulting from the use of this information. Before beginning any project, study your instructions carefully and if any doubts or questions remain, always consult with a local professional or expert. Always check to see that your project complies with all applicable local codes and regulations. Read and follow all safety precautions provided by tool or equipment manufacturer.


Working With Copper Pipe

1 - TYPES OF COPPER PIPE


There are two basic types of copper pipe or tubing: rigid and flexible.


Rigid pipe, usually installed in new homes, makes a neater installation, but it is much more difficult to install than soft, flexible copper pipe.


Flexible copper pipe is best for repair work since it can be run around obstacles without connections or cuts.


Copper pipe is available in three basic types: Type M is thin-walled, Type L is medium-walled and Type K is thick-walled. In most cases, Type L is good for home use. Check your city code to determine which type of pipe is required for the work you're planning.


Fig. 1 shows the inside and outside dimensions of medium-weight, Type L copper pipe.


Image


2 - COPPER PIPE FITTINGS


Fig. 2 illustrates the three basic categories of copper pipe fittings. The first category includes fittings designed for making bends and turns in the pipe. The second category has fittings made for joining or branching copper pipe.

Image

FIG. 2 - Cat. 1: copper pipe fittings for making blends and turns; Cat. 2: fittings for joining or branching pipes; Cat. 3: other copper fittings.


The final category includes couplings, slip couplings, cast iron pipe adapters, etc. You can use any of these fittings on either rigid or flexible pipe.


The fittings illustrated are by no means the complete array of copper pipe fittings. Other fittings are available to help solve special piping problems.

3 - CUTTING COPPER PIPE


You can cut copper pipe with a regular hacksaw or a copper tube cutter (Fig. 3). Although both will make a satisfactory cut, the tube cutter ensures a square cut every time.

Image

FIG. 3 - Use a hacksaw or tube cutter to cut copper pipe.


Use a jig or miter box when you're cutting copper pipe with a hacksaw. This helps to ensure a square cut in the pipe.


You can make a jig from a wooden board or block with a vee notch sawed out to hold the pipe in place.


A slot in the jig will guide the saw at right angles to the vee notch, making it easy to hold the pipe while cutting and helping ensure a square cut.


When using a pipe cutter, hold the copper tubing in place with a pipe vise or some other holding device.


After making the cut, remove the burrs inside the pipe with a half-round file. A pipe cutter usually leaves more burrs in the pipe than a hacksaw.


When cutting pipe for a specific run, be sure to make allowances for the distance of pipe that fits into the fittings. Also, remember to add the extra length the fittings will give the entire run of pipe. Figure about 1/2" for each fitting.

4 - SWEATING A JOINT IN COPPER PIPE


After you've cut the copper pipe to the proper length, clean the end of the pipe with a 4-in-1 tool. Clean the area to be inserted in the fitting until it is bright all around. You can also use a separate brush, fine sandpaper or steel wool.


If you're using the 4-in-1 brush, slide the pipe inside the brush. The standard 4-in-1 tool will clean both 1/2" and 3/4" pipe and fittings. Be sure you are using the right size. Turn the tool back and forth until the pipe is bright. You can also hold sandpaper or steel wool around the pipe with light pressure. Then turn the tube back and forth several times.


You must also clean the inside of all fittings. You can use the 4-in-1 tool, brush, steel wool or sandpaper. Take the time to clean them thoroughly. Debris or foreign matter left in the pipe causes a poor seal.


Next, apply a light coat of soldering paste or flux to the cleaned end of the copper pipe (Fig. 4). Use a flux brush, an old toothbrush or a wooden paddle for spreading the flux.

Image

FIG. 4 - Spread flux evenly on the cleaned end of the copper pipe.

Flux or soldering paste ensures a firm bond between the copper and the solder.


Also apply flux to the inside of the cleaned fittings (Fig. 5). Use a flux brush, wooden paddle or toothbrush to apply the soldering paste.

Image

FIG. 5 - Rub flux into the cleaned fittings.


The flux or soldering paste will keep the copper from oxidizing when heated.


Never use acid core solder for sweating copper pipe.


Place the copper fitting on the pipe only after it is thoroughly cleaned and coated with soldering paste (Fig. 6). When the fitting is firmly in place, rotate both the pipe and the fitting several times to spread the flux evenly.

Image

FIG. 6 - Place the fitting on the pipe in its final position, rotating the joint several times.

A propane torch is an ideal tool for sweating copper pipe. If you look at the flame of a propane torch you will notice there is a lighter blue, well-defined flame in the middle of a darker blue flame. The tip of this light blue flame is the hottest part of the flame (Fig. 7).

Image

FIG. 7 - Use a propane torch to apply heat for soldering.


Play the flame along the fittings and the pipe to bring them up to soldering heat. Then concentrate the heat in the middle of the fitting. The light blue flame should be just touching the fitting. You can do both ends of the fitting at the same time by heating in the middle like this.


Do not apply the heat directly to the solder or the area that has been fluxed. Do not overheat the copper pipe. If you look at the flame on the side of the pipe away from the torch, you may notice a green flame develop. This means the fitting is ready to solder. Another way to tell is to touch the solder to the hot pipe. If the solder melts and begins to run, the pipe is at soldering temperature.


Remove the flame from the pipe and apply the solder to the pipe where it joins the fitting. The solder will flow into the fit. Keep melting the solder until it appears completely around the fitting. The old saying, "If a little is good, then a lot is better," does not apply here. Excess solder can run down inside the pipe, causing a restriction or even a blockage.


Many codes now require lead-free or nearly lead-free solder to be used for water supply lines. Check with your local code to be sure. Never use acid core solder for sweating copper pipes. Use either lead-free or 95/5 solid-core solder.


If you are soldering both sides of a coupling or elbow or three sides of a tee, do it all at the same time. Heat the fitting and then quickly apply solder to all the joints. If you have to reheat a joint on a fitting, place a wet cloth on any nearby joints that have already been made. This can avoid damaging these nearby joints.


You can experiment with different tips on your propane torch until you find the one that spreads the heat evenly along the pipe you are using.

5 - MENDING COPPER PIPE


At some point, you may need to repair a leak in copper pipe or replace a damaged section with a new piece.


You can use either a standard copper coupling of the proper size or a slip coupling for making repairs or inserting a new section in copper pipe (Fig. 8).

Image

FIG. 8 - A standard coupling has a center ridge–the slip coupling is smooth inside.

The basic difference in a slip coupling and a standard coupling is the center ridge built into a standard coupling. Both fittings can be used for the same mending purposes, but the center ridge in the standard coupling makes it easier to center the fitting on a repair job.


The ridge in the standard coupling automatically centers it when the coupling is used for making a splice in pipe. The slip coupling can be slid along the tube, but it must be centered by measuring at each joint.


Small leaks in copper pipes can usually be corrected by sawing the pipe directly at the point of the leak (Fig. 9).

Image

FIG. 9 - Cut the pipe at the leak and mend with a slip coupling.


First, drain all the water from the pipe. Spread the pipes apart and insert a slip coupling or a standard coupling of the proper size over the pipe.


If you use a slip coupling, insert it on the pipe and slide it to the desired position. The center ridge in the standard coupling makes slipping impossible.


Clean the two ends by brushing, sanding or rubbing as previously described.


Clean the ends of the pipe. Apply the flux to the pipe and fitting. Solder the slip coupling into position as shown in Fig. 9.


In some cases, a section of pipe must be totally cut away and removed (Fig. 10). You need to saw away the section of damaged pipe and cut a new piece of pipe of the same size and length.

Image

FIG. 10 - Completely cut out and remove the section of damaged pipe.

Remove the damaged pipe and replace it with a new section of pipe that is exactly the same size (Fig. 11). Clean the ends and the inside of the couplings.

Image

FIG. 11 - Remove the old pipe and replace it with a section of new pipe.

After applying flux, put the two slip couplings into position and prepare for the sweating process.


Solder the slip couplings into place (Fig. 12). Use lead-free or 95/5 solid-core solder only. Never use acid-core solder for sweating copper pipe.

Image

FIG. 12 - Solder the slip couplings into place.


Many older homes were originally plumbed with galvanized pipe. However, you can still use copper pipe when repairing the plumbing system.

6 - Lead Warning


Many older homes have lead pipe water systems. Many newer homes have copper pipe water systems that have been soldered together with solder containing lead.


Lead can leak into the drinking water system from the corrosion of materials in plumbing and distribution systems that contain lead. Exposure to lead may cause brain and nervous disorders, anemia, high blood pressure, kidney and reproductive problems, decreased red blood cells, slower reflexes and even death. The lead collects in the kidneys, liver and brain. Unlike many other chemicals, once lead enters a person's system it cannot be removed. Exposure to even small amounts over a period of years can cause irreversible damage.


When working on a plumbing project, use lead-free solder.


In normal use, if it has been six hours since the water system was used, turn on the water and let it run for a few minutes before drawing water to use for drinking or cooking. However, there is no need to waste this water. It may be used for such things as watering plants.


Additional information is available from the Environmental Protection Agency's Safe Drinking Water hotline at 1-800-426-4791. It can also provide information about certified laboratories that test for lead in drinking water.


Contact the National Lead Information Center Hotline at 1-800-LEAD-FYI for more information and lead poisoning prevention.


TOOL AND MATERIAL CHECKLIST
Copper Pipe Hacksaw
Pipe Cutter Sandpaper
Stiff Brush for Flux 4-in-1 Cleaning Brush
Propane Torch Hand Cleaner
Pipe Fittings & Connectors Pipe Vise
Half-Round File Steel Wool
Flux or Soldering Paste Lead-Free or 95/5 Solid-Core Solder
Extra Propane Tank


Check your state and local codes before starting any project. Follow all safety precautions. This information has been furnished by the National Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor, OSH, nor any retailer can be held responsible for damages or injuries resulting from the use of this information. ))))))

Posted: Sat Feb 24, 2007 7:54 am
by Hotwired
Remember NOT to use a pipe cutter for your barrel.

Pipe cutters use a circular cutting disk which presses into and cuts the copper. It also squeezes it inwards leaving a significant inward rim which can block projectiles.

Use a hacksaw for barrel ends and grind/sand any burrs off.


*edit: I've been reminded theres the pointy bit on pipe cutters to remove said rim but nevertheless I still believe a hacksaw gives a better result.

Posted: Tue Feb 27, 2007 12:56 pm
by Copperboy
I often have trouble heating up the pipes enough so that the solder melts...
Well, it´s of to the store to find some better solder... though i think what I have now is 95/5

Ore you could use an oxy/ace burner to heat it up:)

Anyone have the same issues?

Posted: Fri Mar 09, 2007 6:41 pm
by WOW!!
Hotwired wrote:Remember NOT to use a pipe cutter for your barrel.

Pipe cutters use a circular cutting disk which presses into and cuts the copper. It also squeezes it inwards leaving a significant inward rim which can block projectiles.

Use a hacksaw for barrel ends and grind/sand any burrs off.
You can use a pipe cutter, they usually have a de-burrer on them to remove the inward material.

Posted: Fri Mar 09, 2007 6:54 pm
by zeigs spud
Copperboy wrote:I often have trouble heating up the pipes enough so that the solder melts...
Well, it´s of to the store to find some better solder... though i think what I have now is 95/5

Ore you could use an oxy/ace burner to heat it up:)

Anyone have the same issues?
i LOVE Solder! lol i think it is fun to play with. use a blow torch to heat it. nver had a problome with it.

Posted: Mon Mar 19, 2007 5:38 pm
by GalFisk
Same here, never had a problem with 95/5 (Ag) and a good propane torch.
A pipe cutter is very nice for cutting the breech end for a barrel sealer, as it creates a verystraight and even edge. A bonus is that your projectile won't be able to fall onto the valve.
Good howto, I've seen the original site before. I like zinc chloride soldering paster, it works well and is easy to apply, and can be washed off with mineral spirits (aka white spirit aka paint thinner).

Posted: Sat Mar 31, 2007 11:41 pm
by MisterSteve124
Pipe Cutters are fine for cutting barrels. They have the triangles on the side for a reason. You push it in the pipe and twist it and it grinds away the metal that was pushed in.

Posted: Sat Mar 31, 2007 11:48 pm
by subterranean
Hotwired, im suprised you didn't know about the triangle on a pipe cutter, considering your amazing work with your copperhead prime cannon. nice work! Btw

Posted: Sun Apr 01, 2007 4:13 am
by Hotwired
I never said I didn't, I just didn't remember that bit when typing the post :wink:

I find the effects of a good hacksaw cut and some wire wool are better than squeeze cutting with a pipe cutter then twisting the pointy thing in the end to remove the internal lip.

I think I'll edit my first post actually.