Page 318 of 443

Posted: Tue Feb 19, 2013 1:46 am
by Zeus
Yusef? Your Ipad's autocorrect likes a bit of <s> Simon and Garfunkel?</s> Cat Stevens, what the fuck was I smoking last night?

It's a sound synth, and I'm certain I could find quantities of one of the reagents far easier than the product of the reaction...

Posted: Tue Feb 19, 2013 2:19 am
by jackssmirkingrevenge
Dawn, I've got autocorrect set on "fundamentalist" :roll:

Posted: Tue Feb 19, 2013 4:22 pm
by jakethebeast
Got some parts today

14.5" .22 crosman barrel, 4x 22xx barrel bands, epicly nice breech that Gippeto machined for me with SS bolt and 2250B gas tube.

Now just waiting for the packet from USA to get this thing in action :D

Image

Image

Posted: Tue Feb 19, 2013 5:06 pm
by jackssmirkingrevenge
Is this where gipetto shows us the knife he received in return :D

Posted: Tue Feb 19, 2013 5:21 pm
by jakethebeast
This time it was pure benjamins :D

Posted: Tue Feb 19, 2013 5:26 pm
by Gippeto
Kind words from abroad. (don't Jack...just...don't :lol: )

The parts seem to have beaten the main feature to the door. Hope your 2240 shows up soon so you can finish things off....should be a sharp looking piece. 8)

Enjoy the parts Jake. :)

Posted: Tue Feb 19, 2013 5:31 pm
by jackssmirkingrevenge
Gippeto wrote:Kind words from abroad. (don't Jack...just...don't :lol: )
You must have left her a hefty tip :D

Posted: Wed Feb 20, 2013 5:29 pm
by Gippeto
jackssmirkingrevenge wrote:You must have left her a hefty tip :D
:lol:

Voice of experience there Jack?

:)

Posted: Wed Feb 20, 2013 11:38 pm
by Zeus
Have a looky at what I found

No excuses now hybridless noobs, $12 manometric metering.

Posted: Wed Feb 20, 2013 11:39 pm
by jackssmirkingrevenge
Gippeto wrote:Voice of experience there Jack?
Well I've er... been told that even if one is aware that it is all part of the act, a little flattery and the stroking of um... egos does go some distance towards loosening the purse strings :roll:
Zeus wrote:no excuses now hybridless noobs, $12 manometric metering.
A syringe is still cheaper :)

Posted: Wed Feb 20, 2013 11:48 pm
by Zeus
Indeed, but a certain person has done in excess of 70 attempted shots with a 45cc hybrid using syringe metering with no success, and that's with favourable chamber geometry...

Posted: Wed Feb 20, 2013 11:59 pm
by jackssmirkingrevenge
Has the gentleman tried using a manual pressure device as opposed to something lifted from an ailing refrigerator?

Posted: Thu Feb 21, 2013 12:08 am
by Zeus
I've done a good dozen with a hand pump, and I'll do a lot more this evening. I know the spark gap works, without charging the chamber I get a 12mm arc to the centre terminal, when I take it up to 40 Bar, I get perhaps a 3mm spark. If I had an accurate gauge at those pressures I'd purge the chamber and try it at 33 Bar

Posted: Thu Feb 21, 2013 12:16 am
by jackssmirkingrevenge
I would test at 10x. Are you absolutely sure that you don't have any leaks? Even a tiny one will throw your mix off in the time it takes you to disconnect the pump.

Posted: Thu Feb 21, 2013 12:19 am
by Zeus
I lose about 1cc a minute at 40 bar, but the compressor has a slight leak at the connector. Most of my tests have been at 12x, but I've been down to 4 and up to 16, the limit of my good gauge.