Homemade Lathe?
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
I thought about an idea for a homemade lathe attachment for a bench grinder. It's pretty much just threading the chuck onto the bench grinder and bolting the grinder to a very precisely cut mounting plate with the opposing chuck bolted down across from it.
- Attachments
-
- I've yet to see anyone try this.
- Homemade lathe.JPG (19.74 KiB) Viewed 12574 times
-
- Homemade lathe Chuck.JPG (19.99 KiB) Viewed 12574 times
- jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
A more sophisticated version: http://www.instructables.com/id/Bench-L ... nderSharp/
hectmarr wrote:You have to make many weapons, because this field is long and short life
wouldn't a bench grinder be too fast? maybe using a 90 degree twist belt from a pulley held in a bench or pedestal drill press. you'll have variable speed with the drill press and then you can also easily mount/remove the pulley( for other drilling operations.)
sure, eventually you'll bugger the bearings in the drill press from side load, but i'd rather chance that then slow spooling up speed of the grinder and also the risk of something spiting out at 2000 rpm.
sure, eventually you'll bugger the bearings in the drill press from side load, but i'd rather chance that then slow spooling up speed of the grinder and also the risk of something spiting out at 2000 rpm.
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
That's remarkable. Blows mine out of the water. However, mine is more suited to a more budgeted and not so skilled builder. It'd take me weeks just to build that from plans.
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
That's understandable. Normally, lathes spin slower for harder materials but I guess you could throw in an CVT on a turn knob adjustment. That would give completely variable speeds. It would be expensive though and that kind of defeats the purpose.jerome wrote:wouldn't a bench grinder be too fast? maybe using a 90 degree twist belt from a pulley held in a bench or pedestal drill press. you'll have variable speed with the drill press and then you can also easily mount/remove the pulley( for other drilling operations.)
sure, eventually you'll bugger the bearings in the drill press from side load, but i'd rather chance that then slow spooling up speed of the grinder and also the risk of something spiting out at 2000 rpm.
EDIT: NO! Double post. Sorry!
- Technician1002
- Captain
- Posts: 5189
- Joined: Sat Apr 04, 2009 11:10 am
One important safety item. DO NOT leave any screws extending out of the chuck. They were known for eating clothing and what ever was contained inside the clothing. Recess the adjustment screws and have the jaws move on screws that don't extend out.
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
Good note. I myself only wear t-shirts but I will definitely do that. Don't want to lose a limb.
- pipeboyswe
- Private 3
- Posts: 40
- Joined: Tue Sep 01, 2009 8:52 am
- Location: Sweden
Or more than a limb....Mr.Tallahassee wrote: Good note. I myself only wear t-shirts but I will definitely do that. Don't want to lose a limb.
WARNING VERY GRAPHIC!
http://img1.uploadhouse.com/fileuploads ... 2773e1.jpg
- velocity3x
- Corporal 4
- Posts: 828
- Joined: Fri Jun 05, 2009 3:09 pm
- Location: Yuma, Arizona
- Contact:
I think mounting the motor and a "tail stock" is the easiest part of the project. What about a tool post, cross feed and screws? Why have bearings in the tail stock? Tail stocks are normally dead.Mr.Tallahassee wrote:It's pretty much just threading the chuck onto the bench grinder and bolting the grinder to a very precisely cut mounting plate with the opposing chuck bolted down across from it.
- mattyzip77
- Sergeant 3
- Posts: 1249
- Joined: Tue Jun 28, 2011 12:22 pm
- Location: Taxachusetts
wow, not to get off topic, but that picture is un real!!! It will definatly make me think about safety next time I use a lathe, or anything else for that matter!!!!
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
Actually, they aren't "dead". They normally have small rollers on high speed bearings that run along the surface of the work material but this works essentially the same. I didn't include the tool rest but it just bolts along the edge of the mounting plate and will be adjustable. This was really meant for just machining pistons and o-ring grooves, nothing complicated. I probably should also do a diagram of the mount.
- Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
That needs to be made into a "motivational poster" for shop safety.pipeboyswe wrote:
Or more than a limb....
-------
Anyway, thanks for mentioning the recessed adjustment screws. I was sketching up chuck ideas myself just the other day and would never have thought of that.
Also, in the sudden velocity change you experience when getting sucked into the "lathe" end, you're likely to grab on to something to push back against, which will probably be the "grinder" end
- velocity3x
- Corporal 4
- Posts: 828
- Joined: Fri Jun 05, 2009 3:09 pm
- Location: Yuma, Arizona
- Contact:
Below is a pic of a typical tailstock on a manual lathe. It looks exactly like the tailstock on my lathe. I could be wrong but..............it sure looks dead to me.Mr.Tallahassee wrote:Actually, they aren't "dead". They normally have small rollers on high speed bearings that run along the surface of the work material .......
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
The live tailstocks are becoming increasingly more common so why not upgrade?
http://en.wikipedia.org/wiki/LatheTraditionally, a hard dead center is used together with suitable lubricant in the tailstock to support the workpiece. In modern practice the dead center is frequently replaced by a live center, as it turns freely with the workpiece — usually on ball bearings — reducing the frictional heat, especially important at high speeds. -Wikipedia
- velocity3x
- Corporal 4
- Posts: 828
- Joined: Fri Jun 05, 2009 3:09 pm
- Location: Yuma, Arizona
- Contact:
Correct but....... You are confusing the terms "Center" with "Tailstock". A Tailstock and Center are not the same thing. Tailstocks are DEAD........otherwise they couldn't be used for drilling. Whatever tool the operator chooses to insert into the tailstock (i.e. Live Center, Dead Center, Drill Chuck, etc.) is another matter but, the Tailstock does not turn ergo.....it's dead.Mr.Tallahassee wrote:. In modern practice the dead center is frequently replaced by a live center..........