.22 revolver
ok i was walking around in a flea market and found a box of these by a trash can theres about 400 of them an i dont have the right kinda ramset so i was wondering if anyone here could help figure a way to set up a revolver that would spin them as i shoot.
thats all i need is a revolver setup i got the barrell an stuff
thats all i need is a revolver setup i got the barrell an stuff
- judgment_arms
- Sergeant 3
- Posts: 1272
- Joined: Tue Oct 17, 2006 8:49 pm
- Location: Not so beautiful North Carolina, but at least it’s the U.S.A.!
Your not planning on making a firearm are you? What the heck are those anyway?
-
- Staff Sergeant 3
- Posts: 1762
- Joined: Mon Mar 27, 2006 4:18 pm
- Location: United States
Look like .22 blanks...
-
- Staff Sergeant
- Posts: 1596
- Joined: Fri Dec 15, 2006 3:57 pm
- Location: maryland
- Has thanked: 3 times
- Been thanked: 9 times
maybe its an pellet gun clip, or speedloader for a revolver
- judgment_arms
- Sergeant 3
- Posts: 1272
- Joined: Tue Oct 17, 2006 8:49 pm
- Location: Not so beautiful North Carolina, but at least it’s the U.S.A.!
Ohh… I’ll bet that’s a speed loader for a .22cal revolver.
those are .22 blanks but there for a ramset..
see thats the gun those disks go to.. see the disk in the back of the gun.. the guns are like 200-400 bucks an i dont need one anyway..
no not a fire arm i just want to make a cheap little system to fire of these blanks like on 4th july or whatever
edit: those guns shoot nails into concrete and steel plates and stuff
see thats the gun those disks go to.. see the disk in the back of the gun.. the guns are like 200-400 bucks an i dont need one anyway..
no not a fire arm i just want to make a cheap little system to fire of these blanks like on 4th july or whatever
edit: those guns shoot nails into concrete and steel plates and stuff
-
- Staff Sergeant 3
- Posts: 1762
- Joined: Mon Mar 27, 2006 4:18 pm
- Location: United States
I was just thinking that! I got back from a minute Home Depot a minute ago and I was looking at some ramsets. You're right...
- judgment_arms
- Sergeant 3
- Posts: 1272
- Joined: Tue Oct 17, 2006 8:49 pm
- Location: Not so beautiful North Carolina, but at least it’s the U.S.A.!
Of course you can get them on a plane, duck tape them to your head than put on a wig, when you go through the metal detector just tell them you got a plate in your head! No don’t because if you get caught you’ll be in big trouble, and I’d probably end up in the same predicament.
-
- Staff Sergeant
- Posts: 1596
- Joined: Fri Dec 15, 2006 3:57 pm
- Location: maryland
- Has thanked: 3 times
- Been thanked: 9 times
dough I didnt think of a ram set you can always buy them at the store, but how the heck can you build a revolver, one of the reasons it took a while for the revolver to be invented is because machining technology wasn't good enough. how good are you at machining (metal)? if you're good you could make a pepper box, if your an extremly good expert then you could make a revlolver. if not than you got to have a prebuilt gun or ramset gun[/i]
- Pete Zaria
- Corporal 5
- Posts: 954
- Joined: Fri Mar 31, 2006 6:04 pm
- Location: Near Seattle, WA
It probably classifies as "solid propellants" and thus can't be discussed here, but I'm just thinking, if those .22 blank cartridges can drive a nail into concrete, they could probably propel a marble quite well Building a single-shot, .22-blank cartridge-fed marble gun wouldn't be that hard. Chamber that takes a cartridge in the back, barrel, hammer/trigger setup... done.
Peace,
Pete Zara.
Peace,
Pete Zara.
well i dont think it works quite the way you think it does... the blanks itself dosnt propel the nail the blank goes off pushing a heavy steel piston against the nail "ramming" it into the concrete or steel.
i think thats about how it works and it be hard to make one to shoot a marble with somthing strong enough to stop the piston thats launching the marble be made out of pvc... and i dont feel like nor do i know how to machine anything to do that out of metal...
i think thats about how it works and it be hard to make one to shoot a marble with somthing strong enough to stop the piston thats launching the marble be made out of pvc... and i dont feel like nor do i know how to machine anything to do that out of metal...