Pistonsss

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 9:03 pm

Im gonna make a barrel sealing piston gun, vent it with a blowgun.

THe piston will only be 40mm so that would be okay for venting.


My question is, what do i do with the T? do i put 40mm pvc in it so the piston has a smooth surface with no lumps in it?

what about the third socket? that would be covered from the pipe.

thanks
User avatar
Rudesill Ballistics
Private 3
Private 3
Posts: 57
Joined: Mon Jun 13, 2005 7:42 pm

Thu Sep 06, 2007 9:14 pm

One socket is the barrel/outlet, the opposite socket is the pilot (hook another valve to this part), the third socket is connected to your tank/chamber.

Your piston must seal against the barrel port if it is a barrel sealer.
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 9:26 pm

Mr.Russ wrote:Im gonna make a barrel sealing piston gun, vent it with a blowgun.

THe piston will only be 40mm so that would be okay for venting.


My question is, what do i do with the T? do i put 40mm pvc in it so the piston has a smooth surface with no lumps in it?

what about the third socket? that would be covered from the pipe.

thanks
I suggest you learn your piston valves a bit better before starting out.
Read <A HREF="http://www.spudfiles.com/forums/how-to- ... l">This</a>
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 10:31 pm

thanks mrcrowley that helped alot.

im going to make one like that but with a marble barrel and a 2" chamber.

My deodorant can has about 2mm difference to the ID of my 2" pipe. could i just wrap it in tape to make the difference?
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 10:39 pm

You could, but it could jam up after awhile, do you have Lynx over there? My can is actually from some foot spray stuff, I figured it fit slightly better then a Lynx can.

Lynx is a pretty good fit, it slides so well it builds up pressure and when you let it go, it flys out the pipe...Good times :P
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 10:41 pm

yehh we have lynx over here. i think this gap is to big. i can get a photo for you if ya want..
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 10:50 pm

Hmm thats weird, what pipe ya using? Im used 50mm PVC PN12, maybe your has a different pressure rating.
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 10:57 pm

i wouldnt have a clue what the pressure rating is, bought it at bunnings they just said it was pressure pipe.

after i think about it its not that much of a difference. heres the can pushed completely to one side of the pipe
Image



also - about the sealing face. do you know if the material underneath mouse pads are alright? if they seal? someone on here said they used that.
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 11:02 pm

The mouse pads can be to porus, in other words, to foamy, they can leak air into the barrel. Just go to bunnings and pick up a rubber gasket(usually black or orange) and get the thickets one you can find.

Check the pipe, it should have PNXX on it, the XX is where a number will be, like mine is PN12, PN12 = Pressure Number 12 BAR, which is around 175psi.
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 11:15 pm

okay. i only have 25cm of the pipe left.. was going to use that as the chamber is that enough?


ill check the other part of it on my gun too.
Last edited by Mr.Russ on Thu Sep 06, 2007 11:20 pm, edited 2 times in total.
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 11:18 pm

Yeah it should be fine for marbles.
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 11:21 pm

I checked it, this part of the pipe has no writing on it.

Image

Thats my design.. pretty similer to yours but its a basic version.
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 11:22 pm

Yeah that should be fine, You may have a bit of trouble piloting with a blow gun, but you can try, I recommend at least a 10mm ball valve.
User avatar
Mr.Russ
Specialist 4
Specialist 4
Posts: 429
Joined: Fri Jan 26, 2007 9:07 pm

Thu Sep 06, 2007 11:29 pm

alright. i wanted the blowgun there because its more trigger like, when i twist a ball valve i seem to move the cannon, and sometimes miss a target(uh-oh)

Do you know what brand your pipe fittings are?
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 2 times

Thu Sep 06, 2007 11:31 pm

Yeah I know what you mean, hook it up with a spring maybe, or mod your blow gun, but it may not be enough.

I think marley, can't remember , it shouldn't matter.
Post Reply