Page 2 of 3

Posted: Fri Mar 14, 2008 3:22 pm
by BigGrib
Well for that big of a hole/indent into a 2x4 with a marble is pretty freaking good. I can't wait to see what a lead ball does. very good job, I have been following this gun since it's inception. keep up the posting/updating and I love all the picture cause my imagination sucks.

trigger progress

Posted: Sat Mar 15, 2008 12:47 am
by lockmanslammin
Alright, I got some time at work tonight to use some of the equipment I needed to get the trigger and sear assembly started and got quite a bit done. The trigger itself is made out of 1/4" aluminum, the connecting rod is made out of music wire (real hard steal) and the sear is some 1/8" stainless bar stock welded together and shaped with an angle grinder. All of the pins you see will be drilled and fitted with clips for easy diss-assembly. I'm pretty sure I have it figured out how I will attach it to the cannon, but I will wait until I have it done to take a pic and explain it. There will be a little bit more machining to make the piece that will be the other side of the sear and be threaded and screwed to the ball valve handle. I plan on having the holes slotted for adjustability and precision alignment so it works with the sear perfectly. This baby will have a hair trigger, I was just thinking tonight I need to add some sort of a safety lever to the assembly some where. Anyhow, here is a couple pics of it so far. When it is all assembled there will be a frame piece on both sides, I put them both on the bottom for the pics, so it would be easier to see.

Image

Image

By the way, thanx jsr, biggrip and everyone else, I do appreciate the replies and opinions, this forum, and the people in it,are a large part of what makes this project fun.

Lock

best damage pics and highest PSI yet

Posted: Thu Mar 27, 2008 11:39 pm
by lockmanslammin
For the first time I used some new muzzle loader sabots and a 50 cal. lead round ball. AAAnndd for the first time i pushed it up to 350PSI. I thought my pump was maxing at 302PSI or so, but as it turns out the gauge was just sticking a little or something....a few more pumps and up it kept climbing until I voluntarily stopped at 350PSI. Any how I set a piece of 3/4" MDF against a stud in my garage and then a piece of 1/2" OSB in front of that.

Loaded a slightly stretched out 50 Cal. sabot and 50 cal. lead round ball with a piece of light weatherstripping on top to hold in the bullet.
First pic: entry hole in the 1/2" OSB.....

Image

Next pic: exit hole in 1/2" OSB

Image

next pic: entrance hole in 3/4" MDF

Image

Next two pics: exit hole in 3/4" MDF from two angles, one with the smashed 50 cal. ball for size comparison.

Image

Image

Last pic: The 2X4 stud finally stopped it, but still got about a 1/2" dent in it.

Image

Man, that was the coolest shot yet by far. I am starting to think that I shouldn't shoot it in the garage any more though. Since this time my fiance could here it loud and clear in the living room on the other side of the house while watching TV, and mind you we don't have an attached garage. It would suck to have a cop knocking on my door asking what was going on because one of my neibors thought I was shooting a real gun or something.

Anyhow, I hope to be getting the trigger assembly attached soon so I can update again with actuall cannon construction updates.
as ussual any comments or questions are welcome.
Lock

Posted: Fri Mar 28, 2008 12:03 am
by jackssmirkingrevenge
looking good :) if you're worried about noise there are plenty of suppressor options you can build to mitigate the muzzle blast, though of course projectile impact will still be just as audible.

Posted: Fri Mar 28, 2008 12:45 am
by Gippeto
Good work! When you get the pressure up, the damage gets really impressive...even a little bit worrisome! :shock:

You have to try steel plate, at 350psi you should be splattering your round ball. I know you will if you get it to 400psi. :wink:

Posted: Fri Mar 28, 2008 1:44 am
by lockmanslammin
I think if I shot at a steel plate the round ball would be in little bits all over the garage, (like the wood is currently..hehehe). I think the wood acts as a cushion to the lead slowing it down slowly enough that it remains in one piece. But this is the only shot like this I have taken yet. The last was a 54 cal lead ball at a piddly 120PSI. Now that I know the pump isn't maxing out I will try my previous plan to pump it too 500 psi a few times, and actuating the trigger with a broom from around the corner or something for safety testing, and then sticking to 400PSI for my shots.
I wonder what would happen to it if I had a failure at 4 or 500PSI. After seeing what the bullet does and what it sounds like when it fires it kinda freaks me out a bit actually. I tried to build it as solid as possible. I did a couple xtra things, such as not grinding the pipe stops out of the tee for the piston valve. That always sounded strange to me, like you would be destroying the integrity of the fitting.
I can't wait to see some damage from that insane beast you are building Gippeto. 3,000PSI! WOOOHOOO

thanx for the replies guys.
Lock

some pics of the finished trigger and sear assembly

Posted: Sun Apr 27, 2008 6:21 pm
by lockmanslammin
A few pics of the trigger and sear assembly for my spring actuated ball valve pilot.

Image

This assembly is totally servicable, although I hope it never needs it. I had to build jigs and spacers and all sorts of crap to get it in place accurately. you can see the 3 epoxy attachment points. The epoxy is stuck to the copper pipe, but not to the plexy trigger body. I used a counter sink to make key holes in the inside of the plexy and the puddy epoxy forms the male part of the key. The two screws/ wing nuts hold the whole thing together. It has about a 3 pound trigger pull I'm guessing. The ball valve opens pretty quick, but not too fast to break itself. It is now much easier to aim and hold steady while shooting all I need to add are sights. And then a quick clean up of the solder joints and I believe it is done.
Here are some more pics showing different aspects of the design.

Image

Image

Image

Image

Image

If any body has any comments of questions, I would be happy to answer them.

Lock

Posted: Sun Apr 27, 2008 6:45 pm
by THUNDERLORD
Great stuff!!! I was looking at your photos of build/ sear especially and thinking that your username should be kalishnikov or something. Thanks :wink: 8)

Posted: Sun Apr 27, 2008 9:47 pm
by jackssmirkingrevenge
slick, would be great to see a video of it in action :)

Posted: Sun Apr 27, 2008 11:00 pm
by Gippeto
That's some nice work Lock.

Two thumbs up! :D

Posted: Sun Apr 27, 2008 11:06 pm
by bigbob12345
Wow very impressive work
seems to have good power too it

Posted: Mon Apr 28, 2008 11:33 am
by lockmanslammin
Thanx for all the nice comments fellas. Getting that assembly on the cannon, squarely, was the hardest part of this build.

JSR: I was thinking of trying a video. I have never posted a video online, and I don't have a digital video camera other than the video clip function on my fuji digital camera, and my web cam. Still I may try to post one.

It works real slick. My only concern is that I never added a bumper of any sorts, because frankly I just wasn't thinking about it, but I sure could make it open faster if I had one. Although it does open faster than by hand, so it is still an upgrade. Plus its not like the ball valve is my primary valve anyhow.

Lock

Posted: Wed Apr 30, 2008 6:16 am
by jackssmirkingrevenge
lockmanslammin wrote:JSR: I was thinking of trying a video. I have never posted a video online, and I don't have a digital video camera other than the video clip function on my fuji digital camera, and my web cam. Still I may try to post one.
That's exactly how I make my videos ;) all you need then is a youtube account to host them, if you can make a launcher this intricate work that should be child's play ;)

crappy video

Posted: Sat May 03, 2008 4:43 pm
by lockmanslammin
I realise this is a crappy video, but here you go.
For some reason the camera's mic didn't pic up the loud bang this thing puts out at 350 psi. That shot went through like 4 layers of 1/4" OSB (oriented strand board). The projectile was a glass .5" marble in a greased t-shirt patch, sold as a slingshot ammo. The cannon actually has a little kick even with that light of an ammo.
This is the first time I have ever tried posting a video, so I hope it works.

Lock

Image

VIDEO LINK^^^^ VIDEO LINK^^^^ VIDEO LINK^^^^

Posted: Sat May 03, 2008 4:57 pm
by SpudFarm
NICE i love it!
that is some extreme damage with a marble on that two by four! i cant do that with my pneumatic.. my hybrid had trouble with that at 4x..

once more NICE a$$ gun!