Hotwired wrote:A pneumatic.
It was a very odd design... it was a pressurised broom handle and the valve was a short plastic tube with one sealed end. Which was also the barrel.
Pushing the barrel further into the broom handle exposed holes cut into the side of the plastic tube and shot out the pencil or pen or whatever was in there.
Valveless ? Pneumatic
I got this idea from hotwired. so i drew a quick pic to see if u guys think it will work. should be cheap enough to make. the only special item would be the O-ring.
- Attachments
-
Last edited by Spuddin on Tue Jun 10, 2008 9:14 pm, edited 2 times in total.
You lied! You said you wouldn't use a valve! You used a schrader valve! I'm just kidding. In all seriousness, I thought it didn't work at first, but then I read the "slide the barrel back and the air from the chamber enters the holes in the barrel and pow!" part. This might be a little retarded, but wouldn't it be kinda hard to push the barrel back with so much pressure building up behind it?
Happy 200th post, by the way.
Happy 200th post, by the way.
Last edited by n-strike on Tue Jun 10, 2008 8:06 pm, edited 1 time in total.
i have no idea...
ok use a cork instead of the schrader valve.
ok use a cork instead of the schrader valve.
-
VH_man
- Staff Sergeant 4
- Posts: 1827
- Joined: Sat Dec 09, 2006 6:00 pm
- Location: New Hampshire
- Been thanked: 1 time
technically this is a valve...... its the same valve used in inline Pump Paintball guns and the Airforce Condor..........
if you replaced the "pushing back" part with a hammer, youd have a kick-butt hammer valve gun.
if you replaced the "pushing back" part with a hammer, youd have a kick-butt hammer valve gun.
-
SteelSovereignty
- Private
- Posts: 7
- Joined: Tue Jun 10, 2008 6:17 pm
Looks like it might be okay, worth a test I'd say.
If your interested in this kind of operation you might want to check this link out:
http://nerfhaven.com/homemade/zero_semiautovalve/
made for nerfs, but pneumatics are all the same.
I'm not sure how good a moving barrel would be for accuracy, also maybe try to incorporate something to make it not waste all air in one shot?
Just suggestions, looks good!
If your interested in this kind of operation you might want to check this link out:
http://nerfhaven.com/homemade/zero_semiautovalve/
made for nerfs, but pneumatics are all the same.
I'm not sure how good a moving barrel would be for accuracy, also maybe try to incorporate something to make it not waste all air in one shot?
Just suggestions, looks good!
It will work, but it will take:
pi*.5^2*100 = 78.5 lbs of force to open at 100 psi.
The radius of .5 is used because the OD of 3/4" SCH40 is approximately 1"
I say it would be pretty hard to open.
pi*.5^2*100 = 78.5 lbs of force to open at 100 psi.
The radius of .5 is used because the OD of 3/4" SCH40 is approximately 1"
I say it would be pretty hard to open.
<a href="http://gbcannon.com" target="_blank"><img src="http://gbcannon.com/pics/misc/pixel.png" border="0"></a>latest update - debut of the cardapult
What if the end cap on the barrel was replaced with a cone?clide wrote:It will work, but it will take:
pi*.5^2*100 = 78.5 lbs of force to open at 100 psi.
The radius of .5 is used because the OD of 3/4" SCH40 is approximately 1"
I say it would be pretty hard to open.
Where would you find a cone that can be inside a pressurized chamber?
<a href="http://www.danasoft.com"><img src="http://www.danasoft.com/citysign.jpg" border="0"></a><div>
THIS STATES WHERE YOU LIVE, NOT ME, IT SAYS WHERE YOU LIVE BASED ON YOUR IP ADRESS.
THIS STATES WHERE YOU LIVE, NOT ME, IT SAYS WHERE YOU LIVE BASED ON YOUR IP ADRESS.
Nit picking pizlo sees a problem here. You can't move it back instantly, so I figure your projectile will be out the barrel before your holes are a quater open. You probably willget bad performance because of this.
I found this on the search.
I figured ant would have an answer. The only big problem I see is it leaking a bit when the barrel begins to slide (other than the hard opening).
As far as a cone goes, one could surely be improvised or machined.
I figured ant would have an answer. The only big problem I see is it leaking a bit when the barrel begins to slide (other than the hard opening).
As far as a cone goes, one could surely be improvised or machined.
This defiantly could be used for pneumatic cartridges, just shove this into the breech and the bolt would push the back in and the barrel would stop at the main barrel. A bolt/spring mechanism could help with the force needed. THis could also make a cool artillery style cannon with shells, let the weight of the main barrel on large calibers fire the valve.
P.S. A cone has the same horizontal cross section as an endcap so the same amount of force would be pushing in on it.
P.S. A cone has the same horizontal cross section as an endcap so the same amount of force would be pushing in on it.
"There isn't a problem in the world that can't be solved by the proper application of explosives"
-
jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
This is exactly how Saxby-Palmer air cartridges work, though they were replaced by the more compacy and "realistic" brocock tandem cartridges.Atlantis wrote:This defiantly could be used for pneumatic cartridges, just shove this into the breech and the bolt would push the back in and the barrel would stop at the main barrel. A bolt/spring mechanism could help with the force needed.
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
trollhameran
- Corporal
- Posts: 515
- Joined: Tue Dec 04, 2007 5:41 pm
Maybe if you could make the surface area of the cap behind the o ring really small if would make it a bit easier to push the barrel back. How big are the holes in the barrel going to be?