Page 4 of 5

Posted: Thu Mar 04, 2010 1:42 pm
by smirpab
belle avancemment, je te félicite, mais pour ce qui est du corps du pistolet tu l'as démonté d'une réplique ?

Posted: Thu Mar 04, 2010 1:55 pm
by Demon
belle avancemment, je te félicite, mais pour ce qui est du corps du pistolet tu l'as démonté d'une réplique ?
Non, ca vient d'un jouet pour enfant et je fait en faire un vrai en bois moi-meme.

Posted: Thu Mar 04, 2010 2:01 pm
by smirpab
Ah oué ca va être compliqué de refaire toute les finitions .

Sinon ton mini tours, tu l'as acheté combien ?

Posted: Thu Mar 04, 2010 2:04 pm
by Demon
À 280 euros livré :D

Je l'ai eu dans un vente débaras très rare .
Norrmalement c'est 350 euros pas livré

Posted: Thu Mar 04, 2010 4:18 pm
by Demon
In addition to the requirement for an RPAL, restricted weapons in Canada may only be used (legally) on an approved firing range, you'll need a transit permit to carry it from your house to the range as well (don't get caught changing your route plan either), and don't forget safe storage (a biggy!).
Are you sure?

My dad as an acquisition paper (even tough he as no guns) and told me thats the law in the city, but if you are actually one you 1 mile by one mile private territory in the greath with north(or at least far enough from montreal), you can shoot no problem

And it not a pistol, as the barrel makes 530 mm

From what i have understood from the law, its the fact that its small that makes it restricted, but over 105 mm barrel, its not that much problems


And in our great nation, you can buy a cal .50 without much trouble :D

Posted: Thu Mar 04, 2010 4:51 pm
by ramses
Demon wrote: And in our great nation, you can buy a cal .50 without much trouble :D
our wonderful majority party is trying to take them away from us.

That trigger is amazing, do you have an interrupter on it?

Posted: Thu Mar 04, 2010 5:23 pm
by Demon
our wonderful majority party is trying to take them away from us.
Not in canada i hope :x


What is an interupter ?
I have managed to make it work with one side off, it looks really nice :twisted:

The trigger is real smooth (if i placed a ball bearing, it would theoritically be 0 lbs of pull :) ( not counting the spring tough)
I love it :D

EDIT:

UPDATE


Posted: Thu Mar 04, 2010 9:34 pm
by Gippeto
Demon...the law makes no distinction as to "city" or not in regards to this matter. I really don't know what your dad is talking about...or who told him that.

But I thought we had settled this...without meeting BOTH the velocity and energy criteria...it is NOT a firearm and does NOT have to be registered...at all.

Install the relief valve if you need to limit one or the other, and forget about it.

You and your dad should read this;

http://www.rcmp-grc.gc.ca/cfp-pcaf/fs-fd/restr-eng.htm

And check out form CAFC 679. Take a GOOD look.

http://www.rcmp-grc.gc.ca/cfp-pcaf/form ... 79-eng.htm

Yeah...I'm sure....welcome to Canada eh. :(

Posted: Fri Mar 05, 2010 11:38 am
by Demon
I have took a good look and ... the barrel is making 530 mm
So its not restricted right?

Is a cal.50 restricted?

Posted: Fri Mar 05, 2010 2:43 pm
by Gippeto
High-powered air pistols are classified as restricted if their barrel is longer than 105 mm or prohibited if their barrel length is 105 mm or less.
I don't understand why we're still talking about this...keep it UNDER one limit or the other...and forget about it. :)

A quick look through the list of prohibited weapons shows several 50 cal weapons. The Barret 82A1 included. Not restricted...prohibited.

Posted: Fri Mar 05, 2010 5:59 pm
by ramses
Demon wrote: What is an interupter ?
Image

the pink thing in this diagram. Basically, it keeps the hammer from following the bolt as it returns. In firearms, it will usually not result in firing, but without that, the hammer will just stay down. single action. In a hammer valve, it will probably be full auto.

Posted: Fri Mar 05, 2010 6:58 pm
by Demon
A quick look through the list of prohibited weapons shows several 50 cal weapons. The Barret 82A1 included. Not restricted...prohibited.
Is the Sheytac m200 prohibited? (PLEASE not!)
The barret might be prohibited as it is semi automatic ...
The only cal.50 allowed would be the muzle loaded then :(

@Ramses

I dont need an interrupter, as its a single shot ...
And not an hammer

Posted: Sun Mar 14, 2010 1:03 pm
by Demon
What glue should i use to seal a aluminium over aluminium press fit?
Epoxy? What sort of?

I need to know to finish the valve

Posted: Sun Mar 14, 2010 1:35 pm
by Hawkeye
You can use Epoxy on aluminum but you really need to etch aluminum to get a good lasting bond.

Posted: Sun Mar 14, 2010 2:47 pm
by Demon
I think i will be okay without the epoxy finally

EDIT:

I have tested the valve!

It works very well and the trigger is very easy to pull even at high pressures.

Its getting sweet ...