Page 1 of 4

Sniper FX2010

Unread postPosted: Fri Jan 07, 2011 3:28 pm
Author: NENETTE63
hello all :o


8) I'm new and French on the forum is known on the French forum I want to watch the beginning of my realization (PCP Sniper FX2010) idea of a book after


excuse me I just speak English translator
Image

Image

Image

Image


Image

Image
the video
http://www.youtube.com/watch?v=FWGxJpG39XI

Unread postPosted: Fri Jan 07, 2011 3:47 pm
Author: velocity3x
NENETTE63
Welcome to SF. Beautiful design and craftsmanship!

Unread postPosted: Fri Jan 07, 2011 5:52 pm
Author: Mr. Potato Head
WOW! I know this has been said before, but french guns all look amazing for some reason :D
J'aime bien. C'est super cool!

Unread postPosted: Fri Jan 07, 2011 6:13 pm
Author: Gippeto
Very nice! :)

Have any more pictures?

Welcome. :)

Unread postPosted: Fri Jan 07, 2011 6:15 pm
Author: ramses
Nice. You french sure make nice air guns.

What pressure are you filling that HPA tank to with the fridge compressor?
What kind of pipe did you use for the barrel? What size is it? Is it rifled?

With a few modifications, you could combine the mechanisms of the hammer valve and bolt. After that, add a magazine, and...

Add a stock, and it looks like you would have a fairly accurate PCP.

Unread postPosted: Fri Jan 07, 2011 6:45 pm
Author: JDP12
Wow. That's crazy. I am continually impressed by the quality of guns comin out of France.

Good job!

Unread postPosted: Sat Jan 08, 2011 12:39 am
Author: jackssmirkingrevenge
ramses wrote:you could combine the mechanisms of the hammer valve and bolt.


That was my first thought, but beautifully made.

Unread postPosted: Sat Jan 08, 2011 12:56 am
Author: inonickname
jackssmirkingrevenge wrote:
ramses wrote:you could combine the mechanisms of the hammer valve and bolt.


That was my first thought, but beautifully made.


I guess some people would prefer to have the bolt and hammer cock operate separately so they aren't loading a primed gun by hand. I'm sure there's a reason for it, if he wanted that it's obviously within his skill level.

Very beautiful work. I hope you put a stock on it that does it justice :wink:

Unread postPosted: Sat Jan 08, 2011 2:26 am
Author: Butch902
very nice looks like u put alot of time and effort into making that gun.

Unread postPosted: Sat Jan 08, 2011 12:22 pm
Author: SpudFarm
My signature speaks for itself.

Great job on the quality of this. I just can't se why every air gun comming from France is a hundred times better then those from the USA..

Unread postPosted: Sat Jan 08, 2011 12:37 pm
Author: wyz2285
Edited.

Unread postPosted: Sat Jan 08, 2011 1:14 pm
Author: Fnord
if you want some thing like this why don't you just buy one?


'cause he probably had fun building it.
That, and this looks like it's meant for ridiculously high pressures, which commercially would probably cost a lot more than a couple blocks of aluminum and a week of screwing around in the shop.
Stocks aren't hard to make either.

But yeah, this is the same as everything else I've seen from france. Extreme attention to detail and top quality workmanship.
Maybe I should go to france some day...

"So, what did you do on your vacation time?"
"I, uh... worked in local machine shops..."

Unread postPosted: Sat Jan 08, 2011 1:59 pm
Author: NENETTE63
wyz2285 wrote:Sorry i don't have the same opinion like all other's , for me this thing has nothing special at all only machine work and high pressure, the design of this gun it's just a copy of the most common commercial air guns , there isn't any technical innovations. To be honest any body here with a machine can done this or even better. Building this it's a wast of time, if you want some thing like this why don't you just buy one? That probably will be cheaper and better made and with a stock.


good evening

it cost me € 0 for matter, for info in France you need a permit to have a weapon more than 10 joules that's your very expensive, most did not finish my project so critical before!! !

I miss the butt to do buying glasses

total cost of my PCP € 0 me some time to work

thank you
Écouter
Lire phonétiquement
Dictionnaire - Afficher le dictionnaireinterjection0.good evening0.good night

Unread postPosted: Sat Jan 08, 2011 2:15 pm
Author: velocity3x
wyz2285 wrote:To be honest any body here with a machine can done this or even better. Building this it's a wast of time.


So.... can we assume you possess extensive machining, engineering, design skills and money necessary for you to make such a pronouncement on an obviously nice build? :P :P :P

Unread postPosted: Sat Jan 08, 2011 3:33 pm
Author: NENETTE63
good evening

So here I replace my 28 bar mano a mano 60 bar: cheers:
- :arrow: realization of my fake silencer
- :arrow: I went up to 45 bar max because my compressor stops
- :arrow: 2nd video at 45 bar
http://www.youtube.com/v/dvQAiiBDI6c

The fake silencer
Image

Image

Image

+ new valve spring change (cause leakage)
Image

distance draws 15M / 20M vapore 45bar: face:
damage first try (plywood)
Image

Tin platisque very hard 3mm
Image