Page 4 of 5

Posted: Tue May 31, 2011 2:17 am
by wyz2285
Well yes, I have charged my gun up to 30 bar, and it´s strong as hell :D with a 0.45g bb the range is more than 150m;
But if you have a low pressure big tank, I don´t know much about that, But with my tank, at 180 psi, after 20 shoots the pressure drops to about 140 psi.

Posted: Tue May 31, 2011 10:26 am
by warhead052
Heres a link for what I am going to get for parts. Cheap airsoft guns, and tons of parts in them (barrels, triggers, bodys...) http://cgi.ebay.com/LOT-4-AIRSOFT-GUN-S ... 2c5cea0edc

Note, these are all springers.

Posted: Tue May 31, 2011 1:15 pm
by wyz2285
They are sure cheap... But if I were you I won't buy them, as they can't furnace quality partes rather very useful :roll: But that's up to you :wink:

Posted: Tue May 31, 2011 3:11 pm
by clemsonguy1125
And my experience with cheap airsoft guns is that somethimes you can not split the shell in two pieces. They are sometimes fused together. Good Luck

Posted: Tue May 31, 2011 4:19 pm
by warhead052
If I can't salvage anything, it wont be a big loss. As long as my brother is willing to pay, he will be getting an airsoft gun.

Posted: Tue May 31, 2011 4:34 pm
by clemsonguy1125
That works, hopefully you can salvage the shell, as IMO thats the most valueable part, as you can buy springs easily. But I would still. take the springs and barrel if its decent. On one of the pistols I was working on, it had like a 8mm barrel for a 6mm round.

Posted: Tue May 31, 2011 5:26 pm
by warhead052
An 8mm barrel? wtf? Well, I decided to scrap the project. I am going for a 400 fps M14, with extended ris and a red dot scope. Sounds alot better. And worth it for only $40. I might get it instead.

Posted: Tue May 31, 2011 5:49 pm
by clemsonguy1125
Sounds good, where are you getting it from? It sounds good if it works. Is it a springer?

Posted: Tue May 31, 2011 6:02 pm
by warhead052
Airsoft mega store, its a springer. And it works, watched a few vids on it.

Posted: Tue May 31, 2011 6:36 pm
by clemsonguy1125
That sounds good, I have a 30 buck walmart famas that actually works good, It shoots about 380 FPS. The 8mm barrel was on a pistol that actually worked pretty well, it justed wasnt super accurate.

Posted: Tue May 31, 2011 6:38 pm
by warhead052
Yeah, I got a 25 dollar walmart shotgun from a friend who had a friend leave the gun at a war and does not want it back. Its about 400 fps, pump action, pistol grip, and has detachable rails. Not bad, for a freebie! ;) I also have a crosman stinger P9 pistol, springer. 300 fps I think. Not sure.

Posted: Tue May 31, 2011 6:41 pm
by clemsonguy1125
I actually think Im gonna pick up your project, lol.

Posted: Tue May 31, 2011 7:24 pm
by warhead052
Haha. This project? Go for it. Don't forget the copper T that is upside down, and the spring loaded bb tube for the magazine.

Posted: Tue May 31, 2011 7:39 pm
by clemsonguy1125
Yeah Im gonna build the valve into a tee, hook up a fire extinguisher chamber, pilot with wyz's blowgun. Im debating on the loading mech though either tmag detent or a BFB.

Posted: Tue May 31, 2011 7:45 pm
by warhead052
Have fun! All I can say.

Edit, I got a 27" 1/4" rigid copper tube, so the project is back in motion. Turns out my parents wont let me get the airsoft gun, so this is what I am going to make. Going to get the valve hopefully on saturday, and then I will see about the copper T, and the magazine. Gotta figure out the trigger though.