QEV QE-03
Posted: Tue Jan 31, 2012 2:39 pm
Okey,so i bought this today: http://www.ebay.com/itm/G3-8-Pipe-Pneum ... 849wt_1270 is the quality good on it?what do you guys think?
) Nice too see other sweds here 
Page 1 of 1
Posted: Tue Jan 31, 2012 2:51 pm
It will do the job just fine, seen that kind of QEVs on other guns here. Just dont use too high pressure since its not rated for any high pressure ( i wouldent feel safe using it over 250psi ) Nice too see other sweds here
) Nice too see other sweds here Posted: Tue Jan 31, 2012 2:56 pm
Yeeeeah Swedenpipeboyswe wrote:It will do the job just fine, seen that kind of QEVs on other guns here. Just dont use too high pressure since its not rated for any high pressure ( i wouldent feel safe using it over 250psi
.the valve is rated for 10 bars ))Posted: Tue Jan 31, 2012 4:50 pm
phyh, sweden, FINLAND FTW!
But enough with this morking, if i remember correctly, JSR made semi-auto using this exact kind of QEV
But enough with this morking, if i remember correctly, JSR made semi-auto using this exact kind of QEV
Posted: Wed Feb 01, 2012 12:38 am
Posted: Wed Feb 15, 2012 3:53 pm
Okey,i got the valve today i are a bit confused so help med please:)
"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
i are a bit confused so help med please:)"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
Posted: Wed Feb 15, 2012 4:52 pm
Correct !AircannonSweden wrote:Okey,i got the valve today
"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
A = Air Chamber
R = Release
P = Pilot
Posted: Wed Feb 15, 2012 5:05 pm
thank you:)Goats spudz wrote:Correct !AircannonSweden wrote:Okey,i got the valve today
"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
A = Air Chamber
R = Release
P = Pilot
Posted: Thu Feb 16, 2012 12:48 am
... had you read the thread I linked to:
"P" denotes the pilot port, where the slide valve should be attached. Your air supply/main chamber should then be attached to the other end of the slide valve. In this case I hooked it up directly to my compressor. This port is compatible with 1/4" BSP.
"A" is where the firing chamber should be attached. For each shot, all the air that is in this chamber will be emptied. In this case I made a small chamber from a section of PVC pipe with epoxy endcaps, with a 1/4" socket screwed into one end to attach to the QEV. This port is compatible with 1/4" BSP.
"R" is where the barrel or magazine should be attached. This port is compatible with 3/8" BSP.
Posted: Thu Feb 16, 2012 2:10 am
Yes i have read it:)jackssmirkingrevenge wrote:... had you read the thread I linked to:
"P" denotes the pilot port, where the slide valve should be attached. Your air supply/main chamber should then be attached to the other end of the slide valve. In this case I hooked it up directly to my compressor. This port is compatible with 1/4" BSP.
"A" is where the firing chamber should be attached. For each shot, all the air that is in this chamber will be emptied. In this case I made a small chamber from a section of PVC pipe with epoxy endcaps, with a 1/4" socket screwed into one end to attach to the QEV. This port is compatible with 1/4" BSP.
"R" is where the barrel or magazine should be attached. This port is compatible with 3/8" BSP.