OH NO!!! a leak. what is the best way to fix it.

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
whatthehellamidoing
Private
Private
Posts: 17
Joined: Thu Aug 31, 2006 5:53 pm

Sun Sep 03, 2006 3:21 pm

so i got my gun all built, barrel seals very nicely, and i got everything glued up. so i went to pressurize it, and it sprung a leak on the joint between the chamber and the end cap. i am wondering what the best way to patch up a leak is. i cant see any reason why it should be leaking, but i hear a hissing, and my pressure gague reads 0.
User avatar
SpudStuff
Sergeant 5
Sergeant 5
Posts: 1410
Joined: Sat Dec 10, 2005 3:55 pm
Location: Cupertino, California
Contact:

Sun Sep 03, 2006 3:58 pm

Um you obviously DID SOMETHING WRONG
You need to remove the fiting and replace it properly. Apply primer to the fitting then the pipe. When it dries in a couple or seconds Apply glue to the fitting then to the pipe. Use plenty of glue. Quickly push the fitting onto the pipe with a 1/4 turn. Then hold it for 30 seconds. Then wait a full 24 hours for the glue to cure. Then you can pressure test your gun. Perfurably with water or oil.
Last edited by SpudStuff on Sun Sep 03, 2006 5:14 pm, edited 1 time in total.
User avatar
schmanman
Staff Sergeant 2
Staff Sergeant 2
Posts: 1685
Joined: Sat Mar 25, 2006 12:28 pm
Location: Michigan,U.S.A
Contact:

Sun Sep 03, 2006 4:11 pm

jb weld is the best way to fix a leak. and by the way something is one word, spudstuff :wink:
Persistence is a measure of faith in yourself
whatthehellamidoing
Private
Private
Posts: 17
Joined: Thu Aug 31, 2006 5:53 pm

Sun Sep 03, 2006 4:36 pm

yeah i obviously did do something wrong. is there a way to get the endcap off, and is it neccesary to remove the endcap to fix the leak? there is only really one big leak, and the rest seals very nicely. i just need to fix this one spot, and i dont feel like cutting the endcap off (again).
User avatar
WOW!!
Corporal 4
Corporal 4
Posts: 891
Joined: Thu Mar 16, 2006 9:47 pm
Location: New jersey

Sun Sep 03, 2006 4:43 pm

I would do what Schmaman said, get some expoxy and fill the hole. Make sure tho you sand the aera around the hole good like with 100grit paper so that the expoxy will stick to it.
whatthehellamidoing
Private
Private
Posts: 17
Joined: Thu Aug 31, 2006 5:53 pm

Sun Sep 03, 2006 5:03 pm

ok thanks. i started to fill the gap, and it looks like its working pretty well. i will probaly have another question in about an hour, but i think this answers it for now.
User avatar
SpudStuff
Sergeant 5
Sergeant 5
Posts: 1410
Joined: Sat Dec 10, 2005 3:55 pm
Location: Cupertino, California
Contact:

Sun Sep 03, 2006 5:14 pm

And when the cap flies off at 110 PSI...
dinsdale
Private 4
Private 4
Posts: 91
Joined: Sun Aug 27, 2006 12:16 pm
Location: Bowmanville, Ontario (canada)

Sun Sep 03, 2006 5:18 pm

if it still leaks after the epoxy, wrap it in electrical tape.
put on a couple of layers and then use a hairdryer on it to make it gummy.
repeat the process until you've used a whole roll of tape.
this only works for very small slow leaks
User avatar
SpudStuff
Sergeant 5
Sergeant 5
Posts: 1410
Joined: Sat Dec 10, 2005 3:55 pm
Location: Cupertino, California
Contact:

Sun Sep 03, 2006 5:20 pm

ReTaRtEd
dinsdale
Private 4
Private 4
Posts: 91
Joined: Sun Aug 27, 2006 12:16 pm
Location: Bowmanville, Ontario (canada)

Sun Sep 03, 2006 5:26 pm

SpudStuff wrote:ReTaRtEd
actually i had a miniscule leak from the threads on the sprinkler valve.
i was losing about 2 psi per minute, after the tape, no airloss
User avatar
SpudStuff
Sergeant 5
Sergeant 5
Posts: 1410
Joined: Sat Dec 10, 2005 3:55 pm
Location: Cupertino, California
Contact:

Sun Sep 03, 2006 5:32 pm

This is a leak in a jount and he said it was a big one.
User avatar
CpTn_lAw
Corporal 5
Corporal 5
Posts: 987
Joined: Sun Sep 11, 2005 9:10 am
Location: France

Mon Sep 04, 2006 10:22 am

i have a solution for you. Take super glue, or epoxy. Take only the chamber, create a small vaccum (continous) and display a small layer or glue or epoxy where the end cap is. you should see the glue/epoxy enter where the leak is. that's what i did for my coaxial piston (which i'll post here later) and it worked perfectly. hope you get it fixed so you can have fun with your canon!!! see ya
whatthehellamidoing
Private
Private
Posts: 17
Joined: Thu Aug 31, 2006 5:53 pm

Mon Sep 04, 2006 10:36 am

thanks. if i still have leaks after i let the epoxy set for a while longer, ill try this method
User avatar
WOW!!
Corporal 4
Corporal 4
Posts: 891
Joined: Thu Mar 16, 2006 9:47 pm
Location: New jersey

Mon Sep 04, 2006 5:31 pm

Wtf is your problem Spudstuff? What is wrong with trying something different? It he said he did it and it worked what is wrong with that? I think you need to relax. But anyways try doing the vacum thing should do the trick.
OwThatsMyEye
Private 4
Private 4
Posts: 74
Joined: Wed Jun 28, 2006 2:27 pm

Mon Sep 04, 2006 5:39 pm

SpudStuff you really are an asshole the guy said he was new at this so why dont you quit giving shit and shut the hell up!
Post Reply