ideas plz
i want to make a spud gun like an air rifle part from it fires bbs. i am i goin to use a ball valve has its ma first gun and i can get pipes for free from ma grandad as hes a plumber so hes goin to give them to me for free.
i am used to makin robots and stuff like that but spud guns are all new to me
plz give me ideas as i am all new to spud guns plz
Also i have a smk b2 air rilfe which is realy bad so don't buy 1!!!!!!
i am used to makin robots and stuff like that but spud guns are all new to me
plz give me ideas as i am all new to spud guns plz
Also i have a smk b2 air rilfe which is realy bad so don't buy 1!!!!!!
- experament_u2
- Specialist 2
- Posts: 271
- Joined: Sun Aug 06, 2006 5:04 am
- killagorrila99
- Sergeant 2
- Posts: 1100
- Joined: Tue Jul 25, 2006 2:35 am
- Location: Australia.
Little complicated, Why not make a bbmg?
- joannaardway
- Corporal 5
- Posts: 949
- Joined: Mon Oct 09, 2006 4:57 pm
- Location: SW Hertfordshire, England, UK.
Cld u tell me y all ths txt lnguge is ncssry?
Cld u also tell me y the hell this is in this section, and why the double post was necessary within 1 minute of your opening post?
And then the triple posts, within 3 minutes of each other?
There is a button called EDIT for a reason - to prevent you needing to double post.
There is no way that a homemade BB gun will be anywhere near as accurate as a proper air rifle - even the poor one you have ATM, and you'd be lucky to get very much power either.
You'd also be lucky to have all the bits for a BBMG immediately.
Cld u also tell me y the hell this is in this section, and why the double post was necessary within 1 minute of your opening post?
And then the triple posts, within 3 minutes of each other?
There is a button called EDIT for a reason - to prevent you needing to double post.
There is no way that a homemade BB gun will be anywhere near as accurate as a proper air rifle - even the poor one you have ATM, and you'd be lucky to get very much power either.
You'd also be lucky to have all the bits for a BBMG immediately.
Novacastrian: How about use whatever the heck you can get your hands on?
frankrede: Well then I guess it won't matter when you decide to drink bleach because your out of kool-aid.
...I'm sorry, but that made my year.
frankrede: Well then I guess it won't matter when you decide to drink bleach because your out of kool-aid.
...I'm sorry, but that made my year.
soz i am new but i got pipes differet sizes and a ball valve can't rember wat size and i got 10 packs o bb pellets so i got a boot 10.000 bb pellets lol and its in this bit o the web site cus i can make a a bb gun or a spud gun but i am more likely to make a spud gun or somthing like a spud gun
How about a basic spudgun to start with...?
I'm assuming this is copper pipe and thats a ball valve for domestic plumbing (so it will fit copper pipes). I'm also assuming that the ball valve is a common compression fitting one...
2 bits of pipe.
1 ball valve.
1 filling valve from a bicycle tyre.
1 compression fitting (straight or angled).
1 washer (small enough to fit just inside the screw cap of the compression fitting and with a hole large enough for the bike valve stem)
Attach the two bits of pipe to the ball valve.
Attach the compression fitting to the end of one of those pipes.
Cut out the bike valve so theres a small circle of rubber left the size of the washer.
Slip the washer over the bike valve stem.
Put the compression nut over that so the stem pokes through.
Tighten compression nut onto the fitting. Do NOT include the olive.
'Kay. All done.
The rubber circle on the end of the bike valve will press against the washer as you fill it up and stop air escaping or the valve flying out.
Once you've pumped it up pull the ball valve and it'll fire.
I'm assuming this is copper pipe and thats a ball valve for domestic plumbing (so it will fit copper pipes). I'm also assuming that the ball valve is a common compression fitting one...
2 bits of pipe.
1 ball valve.
1 filling valve from a bicycle tyre.
1 compression fitting (straight or angled).
1 washer (small enough to fit just inside the screw cap of the compression fitting and with a hole large enough for the bike valve stem)
Attach the two bits of pipe to the ball valve.
Attach the compression fitting to the end of one of those pipes.
Cut out the bike valve so theres a small circle of rubber left the size of the washer.
Slip the washer over the bike valve stem.
Put the compression nut over that so the stem pokes through.
Tighten compression nut onto the fitting. Do NOT include the olive.
'Kay. All done.
The rubber circle on the end of the bike valve will press against the washer as you fill it up and stop air escaping or the valve flying out.
Once you've pumped it up pull the ball valve and it'll fire.
- drac
- Corporal 4
- Posts: 899
- Joined: Sun Apr 24, 2005 8:56 am
- Location: Avon, NY
- Been thanked: 2 times
You make robots? I thought someone with that mental calibre would have enough sense to make their posts somewhat legible. And to notice that it was in the wrong section. And to not double/triple post.
Topic moved to Pneumatic Cannon Discussion.
Topic moved to Pneumatic Cannon Discussion.