Page 1 of 3

Airsoft Sniper

Posted: Fri Jun 15, 2007 8:45 am
by spudthug
hey guys.. i have been planning this for a while i jsut never got around to it... i am making an airsoft sniper.. but i have a few questions and i need some suggestions...

Specs.

1. main valve- QEV
2. Pilot valve- modified blowgun
3. Filling valve- Schrader
4. Barrel-??? (maybe brakeline? what size for airsoft bbs?)
5. barrel length-???? (can you get brakeline in like 3 foot lengths?
6. barrel cover ???? (i need something so the barrel wont bend waht is the best to use so that it still looks cool??
7. chamber-1"x8-12"
8. Red dot sight and laser sight...

Posted: Fri Jun 15, 2007 8:51 am
by Suppressive Fire
First off this should be in the bb/airsoft area.

Best airsoft barrel is 9/32 brakeline but 5/16 is more commonly available. Biuld the entire gun inside a pvc frame. It will look cleaner and be more durable. I'd use 1.5 - 3 ft length for the barrel depending on preference.

Posted: Fri Jun 15, 2007 8:53 am
by Specialist
if i where you i would just make a inline votex rifle or a cloud like mine. its designed to be a sniper rifle. http://www.spudfiles.com/forums/false-denial-t8761.html and no offense but it looks like a marble sniper rifle more than a bb rifle. you should try both a marble/paintball and a bbmg like mine.

Posted: Fri Jun 15, 2007 9:02 am
by spudthug
i dont want to waste 5 million bbs a minute...i want a sniper... no offense but i do not like the look of that gun...i dont like that other guys cloud that is covered in pvc either...i like bare metal...so all pvc is out of the quesdtion....oh yea btw this gun is all metal....

so i need a good pipe to shroud it still (what size and type?)

is brakeline availiable in 3 feet lengths?


thanks all!

Edit:

did anyone ever notice that airsoft bbs fit perfectly in most 1/8 pipe?

on that note what is .269" in mm

Posted: Fri Jun 15, 2007 11:07 am
by potatoflinger
The Pep Boys store that I buy all of my brakeline from sells it in three foot sections, so you might be able to find it in three foot lengths.

Posted: Fri Jun 15, 2007 11:22 am
by Specialist
at ace the helpful place they have 5/16 copper pipe for like 40ยข a foot. its a good deal too. the cloud i built i started with nothing expect the primer and glue and it was only $25.

Posted: Fri Jun 15, 2007 12:26 pm
by spudthug
how well does 5/16 copper fit airsoft bbs?

on that note what is .269" in mm? again..

Posted: Fri Jun 15, 2007 12:49 pm
by hi
if the ID is .269'' then airsoft bb's are a little small because they are 23 caliber.

so the barrel would be 0.039'' to bigl, which probably wont matter to much.

Posted: Fri Jun 15, 2007 12:58 pm
by iPaintball
Even though they're more expensive, actual airsoft barrels air by far superior to any brakeline or pipe barrels. They are machined to within a few thousandths of an inch of the airsoft bb, and they are perfectly straight and smooth. As for the barrel cover, 1/2'' pipe nipples with some teflon tape wrapped around the ends of the barrel work great.

Posted: Fri Jun 15, 2007 1:05 pm
by jackssmirkingrevenge
spudthug wrote:on that note what is .269" in mm? again..
That would be 6.83mm. for airsoft BBs you want as close to 0.236" as possible.

Posted: Fri Jun 15, 2007 2:50 pm
by Hotwired
You'll only need a small chamber and QEV for this setup if all you're firing is a single BB.

The chamber in the sketch would be excessive if it's to scale.

Posted: Fri Jun 15, 2007 5:10 pm
by MrCrowley
Personally I use a weed-sprayers nozzle as the barrel, I've used it on my clouds and it works fine, there is a very very small gap and the nozzle pipe is usually about 2' long on most weed-sprayers and I just bought the nozzle seperatly for about $3NZD which is like $2.2US. Mine also came with a 1/4" adapter like a compression fitting on the barrel so its easy to connect to your valve/cloud/vortex.

Posted: Fri Jun 15, 2007 6:38 pm
by Fnord
wait, did I miss something? cant you just use a blowgun for a valve instead of a qev? I mean, isnt it kind of overkill for a single shot gun?

I got a 40" lenght of brakeline for my bbmg. It was like $3.50 usd

You could sleeve the barrel in 1/2 or 3/4 pvc, or conduite pip for extra strength.

For a 3 foot barrel, a chamber of just a few cubic inches will work fine.

Posted: Fri Jun 15, 2007 7:11 pm
by shud_b_rite
I have tried making bb guns out of blowguns. It doesn't work that good but it still works. I don't think a qev is overkill, but I think it is overkill to have such a large chamber.

Posted: Fri Jun 15, 2007 7:15 pm
by spudthug
my chamber is going to be 1 inch...maybe 6-10" long

i need something for a cover that wont bend or let the brakeline bend...

maybe 1/4 copper tubing?