New project started
- frankrede
- Sergeant Major 2
- Posts: 3220
- Joined: Thu Jul 20, 2006 9:47 pm
- Has thanked: 1 time
- Been thanked: 1 time
Coaxial piston rifle.
similar to this one
http://www.spudfiles.com/forums/viewtopic.php?t=2494&
but different.
I need to buy a new bushing because I screwed mine up/
Interchangeable barrels+functional silencer for 1/2" barrel.
This tipic serves as a build log.
similar to this one
http://www.spudfiles.com/forums/viewtopic.php?t=2494&
but different.
I need to buy a new bushing because I screwed mine up/
Interchangeable barrels+functional silencer for 1/2" barrel.
This tipic serves as a build log.
Current project: Afghanistan deployment
i wish you luck.
"physics, gravity, and law enforcement are the only things that prevent me from operating at my full potential" - not sure, but i like the quote
you know you are not an engineer if you have to remind yourself "left loosy righty tighty"
you know you are not an engineer if you have to remind yourself "left loosy righty tighty"
- potatoflinger
- Sergeant 2
- Posts: 1136
- Joined: Thu Nov 02, 2006 3:26 pm
- Location: Maryland
I'm in the middle of building an assault rifle, it will have a qev single shot mode, a vortex block full auto mode, and a grenade launcher. So far everything is finished except for the grenade launcher, which will be a diaphragm co-axial. I think I will have it finished in a week or two.
- judgment_arms
- Sergeant 3
- Posts: 1272
- Joined: Tue Oct 17, 2006 8:49 pm
- Location: Not so beautiful North Carolina, but at least it’s the U.S.A.!
Me, nothin’ much, just building a prototype auto-cannon, and designing 6 more
The prototype should be finished by the end of the week, provided all goes per planed and I get off my lazy butt…
Hey that reminds me, I’ve got a flop to post…
The prototype should be finished by the end of the week, provided all goes per planed and I get off my lazy butt…
Hey that reminds me, I’ve got a flop to post…
- spud yeti
- Sergeant
- Posts: 1030
- Joined: Tue May 08, 2007 1:41 pm
- Location: Cape town south africa
- Contact:
Everyones projects sound really good, and Im looking foward to seeing them all.
I'm finishing my semi-auto paintball gun, which is going well, and will hopefully be completed in the next few months (its about 52% complete(that was just a guess))
I am now starting on a prototype(ish) valve which includes a "hammer-piston" valve; hence the (ish) that is only in its early stages though, and could be a while...
I'm finishing my semi-auto paintball gun, which is going well, and will hopefully be completed in the next few months (its about 52% complete(that was just a guess))
I am now starting on a prototype(ish) valve which includes a "hammer-piston" valve; hence the (ish) that is only in its early stages though, and could be a while...
really good quote/phrase here
- Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
Currently I'm getting parts for a hybrid torture test.
The goal is to find out what it really takes to fragment 2 inch sch40 steel.
(No, I'm not going to blow up my hybrid, I'm going to make a closed hybrid chamber and crank up the mix until it pops)
This will of course be done in bunker. If I can't get it to explode(I'm limited to about 8 or 9x), Then I will adjust the spark gap placement to attempt DDT.
The goal is to find out what it really takes to fragment 2 inch sch40 steel.
(No, I'm not going to blow up my hybrid, I'm going to make a closed hybrid chamber and crank up the mix until it pops)
This will of course be done in bunker. If I can't get it to explode(I'm limited to about 8 or 9x), Then I will adjust the spark gap placement to attempt DDT.
- Hailfire753
- Specialist 3
- Posts: 348
- Joined: Thu Jun 28, 2007 11:50 pm
- Location: Near Philadelphia, PA
- Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
Not sure if I will be able to get a video (potential damage to camera and all).
I'll try to see about getting some lexan to set up a camera behind.
Either way you can still expect pictures.
I'll try to see about getting some lexan to set up a camera behind.
Either way you can still expect pictures.
- spud yeti
- Sergeant
- Posts: 1030
- Joined: Tue May 08, 2007 1:41 pm
- Location: Cape town south africa
- Contact:
Currently I'm getting parts for a hybrid torture test.
The goal is to find out what it really takes to fragment 2 inch sch40 steel.
(No, I'm not going to blow up my hybrid, I'm going to make a closed hybrid chamber and crank up the mix until it pops)
This will of course be done in bunker. If I can't get it to explode(I'm limited to about 8 or 9x), Then I will adjust the spark gap placement to attempt DDT.
really good quote/phrase here
- spud yeti
- Sergeant
- Posts: 1030
- Joined: Tue May 08, 2007 1:41 pm
- Location: Cape town south africa
- Contact:
Nope, only me making a semi-auto. Look carefully and you would notice every ones making auto guns. The making them because they awesome thoughskywalker wrote:Howcome everyone is all of a sudden making lots of semi/auto guns
really good quote/phrase here