look at the chamber temperature is that right? over 3500 degrees fahrenheit
and what is chamber burnout?
another hgdt question
- D_Hall
- Staff Sergeant 5
- Posts: 1914
- Joined: Thu Feb 07, 2008 7:37 pm
- Location: SoCal
- Has thanked: 7 times
- Been thanked: 41 times
Yeah, propane burns hot, ya know.
Chamber burnout = The point at which all fuel/air in the chamber have burned. Note that this is NOT the same thing as all fuel/air in the entire system.... When the disc bursts, unburned fuel/air is pushed into the barrel. This fuel/air is NOT burned at the time of chamber burnout.
Now, I'll give you three guesses as to what the meaning of Bar Burnout is.
Chamber burnout = The point at which all fuel/air in the chamber have burned. Note that this is NOT the same thing as all fuel/air in the entire system.... When the disc bursts, unburned fuel/air is pushed into the barrel. This fuel/air is NOT burned at the time of chamber burnout.
Now, I'll give you three guesses as to what the meaning of Bar Burnout is.
can a sch 40 steel pipe handle 3500 degrees?
- bigbob12345
- Staff Sergeant
- Posts: 1516
- Joined: Sat Dec 01, 2007 9:13 am
- Location: Mercer Island,Washington
Well what does everybody use to make hybrids?
And do they have problems with the heat?
The high temp happens so shortly that even pvc chambers wont be affected at all(other than the fact it may burst from the extreme pressure generated )
And do they have problems with the heat?
The high temp happens so shortly that even pvc chambers wont be affected at all(other than the fact it may burst from the extreme pressure generated )
Insulation decreases heat loss, all pressure in chamber is heat, etc...whats with the "insulation" part? my FPS increases significantly when i insulate my chamber........... wich kind of baffles me.
And I'll bet that the reason the burnout messages came up is because your chamber is so ridiculously oversized in comparison to your barrel. Something to do with the fact that the gases haven't fully burned until quite a while after the projectile leaves the barrel.
Spudfiles' resident expert on all things that sail through the air at improbable speeds, trailing an incandescent wake of ionized air, dissociated polymers and metal oxides.
probably 28.5:1 c:b ratioAnd I'll bet that the reason the burnout messages came up is because your chamber is so ridiculously oversized in comparison to your barrel.
- boilingleadbath
- Staff Sergeant 2
- Posts: 1635
- Joined: Sat Mar 12, 2005 10:35 pm
- Location: Pennsylvania, USA
The wall never gets very hot, because the gases don't transfer heat to the wall very fast, at least compared to the rate of heat conduction inside the wall. This holds true even in plastics.
-
- Sergeant Major
- Posts: 3197
- Joined: Wed Mar 28, 2007 9:48 am
- Location: Greenwood, Indiana
- Has thanked: 5 times
- Been thanked: 15 times
- Contact:
Not only do the gases transfer heat relatively slowly, but more importantly, there just isn't that much energy in the gases. Doesn't really matter how hot the gases are, the mass of the gases is so small compared to the mass of the gun that the temperature rise of the gun is minimal.
Even in a closed chamber plastic has no problem handling the heat in the combustion gases. A moderate sized PVC chamber buring 1x propane in air only heats up couple degrees C. The thin layer of PVC in actual contact with the gases gets hotter, but it still isn't hot enough to affect the plastic.
Even in a closed chamber plastic has no problem handling the heat in the combustion gases. A moderate sized PVC chamber buring 1x propane in air only heats up couple degrees C. The thin layer of PVC in actual contact with the gases gets hotter, but it still isn't hot enough to affect the plastic.
2 things: 1) what is ignition number? number of spark gaps?
2) why is there a blue line as well? Whenever i run it i only get a red line
2) why is there a blue line as well? Whenever i run it i only get a red line
"Some say his pet elephant is pink, and that he has no understanding of "PG rated forum". All we know is, he's called JSR. "