Help with Airsoft Sniper

Building or modifying BB, Airsoft, and Pellet type of guns. Show off your custom designs, find tips and other discussion. Target practice only!
bigred225
Private
Private
Posts: 5
Joined: Mon Oct 03, 2016 5:26 am

Tue Oct 11, 2016 9:29 pm

Hi all, I am trying to replicate one of wyz2285's earlier designs seen in this video

[youtube][/youtube]

I have drawn a quick sketch of how I think it goes together but was wondering if somebody could take a look at it to see if its right and if it will work.

Image

Thanks, Bigred
Last edited by jrrdw on Wed Oct 12, 2016 8:20 am, edited 1 time in total.
Reason: Embedded video.
bigred225
Private
Private
Posts: 5
Joined: Mon Oct 03, 2016 5:26 am

Wed Oct 12, 2016 10:30 pm

Also for a reload system, would drilling a small hole out of the joining end of the barrel just big enough for a BB with a sliding cover to seal it and using a magnet underneath to hold it in place work?
User avatar
mark.f
Sergeant Major 4
Sergeant Major 4
Eritrea
Posts: 3628
Joined: Sat May 06, 2006 11:18 am
Location: The Big Steezy
Has thanked: 52 times
Been thanked: 53 times
Contact:

Donating Members

Thu Oct 13, 2016 8:06 pm

Hi there, and welcome!

Your sketch gets the gist of it, however, with "stock" parts that would create a "one shot" (or at the very least a finicky semi-auto where the time you depress the trigger for dictates the amount of air dumped each shot) launcher.

wyz2285 modified his blowgun to only exhaust a small amount of air each time it was depressed. You can see his design in the original thread. EDIT: removed incorrect link.

Also, that loading mechanism can work nicely. I haven't done a sliding cover in the sense you're talking about (or used a magnet to keep the steel BB from rolling, which certainly is nice), but I did use a drilled out compression fitting instead which I simply cranked down over the loading port to seal off the hole and keep the cover in place. (which I am having a hard time finding a picture of... have to get back to you there)

There are also a few more "succinct" ways to do semi-auto with a Q.E.V. and three way valve (simply use the three way to pilot and fill the chamber), and various autoloader techniques you can browse as well.


Good luck with your project, if you have any more questions feel free to post them here.

EDIT:
Image
As you can see I simply drilled out the stop in the compression fitting to slide over the barrel. A quick twist locks it in place.
bigred225
Private
Private
Posts: 5
Joined: Mon Oct 03, 2016 5:26 am

Thu Oct 13, 2016 9:14 pm

Is there any huge downside to 1 shot only? I don't 1 shot, what are the benefits of semi auto?
User avatar
farcticox1
Sergeant
Sergeant
Posts: 1078
Joined: Sun Mar 31, 2013 12:37 pm
Has thanked: 68 times
Been thanked: 94 times

Fri Oct 14, 2016 4:25 am

bigred225 wrote:Also for a reload system, would drilling a small hole out of the joining end of the barrel just big enough for a BB with a sliding cover to seal it and using a magnet underneath to hold it in place work?
That's exactly what I am building now :shock:
User avatar
farcticox1
Sergeant
Sergeant
Posts: 1078
Joined: Sun Mar 31, 2013 12:37 pm
Has thanked: 68 times
Been thanked: 94 times

Fri Oct 14, 2016 3:22 pm

This is my first ever build, single shot is SO much simpler for a first build, I am working on a semi auto now as well.

Image

Image
bigred225
Private
Private
Posts: 5
Joined: Mon Oct 03, 2016 5:26 am

Fri Oct 14, 2016 11:24 pm

Single shot won't empty the entire air tank with 1 shot will it?
User avatar
farcticox1
Sergeant
Sergeant
Posts: 1078
Joined: Sun Mar 31, 2013 12:37 pm
Has thanked: 68 times
Been thanked: 94 times

Sat Oct 15, 2016 7:29 pm

no, good if you have a limited reserve.
Post Reply