Air Tank Materials?

Building or modifying BB, Airsoft, and Pellet type of guns. Show off your custom designs, find tips and other discussion. Target practice only!
User avatar
Hurricane Air Arms
Private 4
Private 4
New Zealand
Posts: 68
Joined: Thu Mar 31, 2016 11:00 pm
Has thanked: 1 time

Thu Jul 14, 2016 9:17 am

Greetings once again.

Most of us started with coke bottles and stuff when we were churning out out first projects when it came to air tanks. For the most part the 2-litre bottles cold safely hold 80psi and had the ability to spit out in excess of 100 BB's which is great for beginners.

Looking at today's most advanced air guns, cylinders of high grade are used and are typically pretty safe, which is my number 1 concern - safety and I think it should be everyone's. SO when I see people pressurising PVC I think back to when my older brothers PVC tank exploded and how lucky he was not to actually be impaled by the subsequent shrapnel.

I'm here to ask what everyone else here uses as an intermediate tank - respectable price and plenty of safety and volume is what I'm thinking. Lots of people use thick copper, some use steel tubes, what do you guys use for your pressures exceeding 100, 150, 200 PSI?
The Lord said "Whom shall I send, and who will go for us?"

And I said

"Here am I...

...Send me"
Doodmens
Private 3
Private 3
Posts: 53
Joined: Tue May 19, 2015 7:44 am

Thu Jul 14, 2016 11:41 am

http://www.copper.org/applications/plum ... burst.html
If you click on the tables you'll see that copper is a pretty good material, and steel is even stronger of course. The critical part here is the joint, so I'd recommend not going above 1000 psi without welded joints
User avatar
Hurricane Air Arms
Private 4
Private 4
New Zealand
Posts: 68
Joined: Thu Mar 31, 2016 11:00 pm
Has thanked: 1 time

Fri Jul 15, 2016 12:51 am

Thanks Man. Very helpful. :)

What's the best way to seal the ends of a copper tank? Threads?
The Lord said "Whom shall I send, and who will go for us?"

And I said

"Here am I...

...Send me"
wdr0
Specialist
Specialist
Posts: 104
Joined: Wed Jul 30, 2014 12:46 am

Fri Jul 15, 2016 8:11 am

For lower pressures standard soft plumbing solder would be fine especially for smaller sizes. Brazing would definitely be best for pressures near the max rating for the pipe.
User avatar
Hurricane Air Arms
Private 4
Private 4
New Zealand
Posts: 68
Joined: Thu Mar 31, 2016 11:00 pm
Has thanked: 1 time

Sat Jul 16, 2016 8:27 am

I'm not confident in soldering nor my abilities, I was thinking of more of a threaded cap?
The Lord said "Whom shall I send, and who will go for us?"

And I said

"Here am I...

...Send me"
User avatar
Gippeto
First Sergeant 3
First Sergeant 3
Venezuela
Posts: 2503
Joined: Sat Jan 19, 2008 10:14 am
Location: Soon to be socialist shit hole.
Has thanked: 2 times
Been thanked: 17 times

Donating Members

Sat Jul 16, 2016 10:33 am

Threaded connections are VERY strong, but sweating copper is a good skill to learn and the equipment (torch, pipe cutter, emery cloth, flux and solder) does not cost a whole lot or take up a lot of storage room.

First off...brazing copper LOWERS the safe working pressure...brazing temperatures anneal the drawn copper tube. Ratings for brazed joints are at the bottom. Copper Tube Handbook is a great resource...suggest downloading the pdf.

http://www.copper.org/applications/plum ... able4.html

Can use 95/5 Tin/Antimony to sweat the copper together...joints have higher strength than 50/50. That said...50/50 is a little easier to use, flows a little better, and might provide a better quality joint for someone with less experience sweating copper. At low pressure, entirely adequate.

Flux is your friend... :wink:

IMHO...the best way to seal the end of a copper tube is with a sweated tube cap.

Image
"It could be that the purpose of your life is to serve as a warning to others" – unknown

Liberalism is a mental disorder, reality is it's cure.
User avatar
Hurricane Air Arms
Private 4
Private 4
New Zealand
Posts: 68
Joined: Thu Mar 31, 2016 11:00 pm
Has thanked: 1 time

Sun Jul 17, 2016 11:26 am

Ahh nice. Thank you.

Let's say I use a length of copper and thread it at both ends, (Basic) what could I expect for maximum safe working pressure? Just off the top of your head.
The Lord said "Whom shall I send, and who will go for us?"

And I said

"Here am I...

...Send me"
User avatar
mrfoo
Specialist 2
Specialist 2
Afghanistan
Posts: 262
Joined: Wed Apr 29, 2015 11:05 am
Has thanked: 73 times
Been thanked: 84 times

Sun Jul 17, 2016 1:21 pm

As close to infinite as you're likely to get. After all, you're talking about a length of solid copper bar, right?

No?

In that case, it will depend on, variously but probably not exhaustively :

- Pipe diameter
- Wall thickness
- Thread type, pitch and depth
- How much of the pipe you're threading
- end cap form

Not knowing the answers to any of the above, off the top of my head the answer would be "some, but no more than that".
User avatar
farcticox1
Sergeant
Sergeant
Posts: 1077
Joined: Sun Mar 31, 2013 12:37 pm
Has thanked: 68 times
Been thanked: 93 times

Sat Jul 23, 2016 10:23 am

- seamless (extruded) or welded ?

And you wouldn't thread copper ? I guess a compression fitting to thread

Image
Post Reply