Page 1 of 2
push pop pneumatic
Posted: Thu Feb 16, 2006 8:14 pm
by cardinals08
Has anyone tried making a piston valve pneumatic gun out of one of these? The thing inside could be used as the piston. All you would have to do is slap a barrel on and attach a schrader valve and possibly drill a couple small holes in the piston and you would be done. It would probably be a good Idea to sleeve it because I dont know how much pressure one of these could hold.
Posted: Thu Feb 16, 2006 10:10 pm
by saladtossser
XD
you can always tie a dozen hose clamps on the make it safer
you need to make a cap for the bottom, think eproxy.
unrelated but you get the idea i hope
Posted: Thu Feb 16, 2006 10:16 pm
by cardinals08
why do I need to make a cap? you mean to make the bottom stronger? or to enclose the bottom(some are open on the bottom because some arent spring loaded to push the pop up), because the one I ate is completely closed on the bottom
Posted: Thu Feb 16, 2006 10:22 pm
by spudshot
that'll blow up in your hand. its not strong enough.
Posted: Thu Feb 16, 2006 10:25 pm
by cardinals08
thats why I said it would be a good Idea to sleeve it
Posted: Fri Feb 17, 2006 2:01 am
by Urban Ninja
I think it would work if you did it right. It might be a bit faulty as that is a 2 dollar piece of plastic. Nice idea, I think itll work.
Posted: Fri Feb 17, 2006 2:12 am
by cardinals08
I might get around to making it, if the one i have will fit nicely in some copper tubing I will start it in a week or so, getting my drivers license about that time to be able to go get parts
Posted: Fri Feb 17, 2006 6:11 am
by nicholai
***PUFF!***
as for the push pop, i think its too cheezy for a pneumatic, maybe at like 10 psi it would be safe
NOTE FROM PIMPMANN22: Removed sexual remarks both because they arent neccesary and the post was off topic. Remeber were on a spudding forum... Dont post anything of this nature again.
Posted: Fri Feb 17, 2006 11:46 am
by cardinals08
***PUFF!***
Why wouldnt it be safe for higher pressure if I sleeved it in copper pipe?
NOTE FROM PIMPMANN22: Removed sexual remarks both because they arent neccesary and the post was off topic. Although you were defending yourself, I think you understand...
Posted: Fri Feb 17, 2006 6:11 pm
by nicholai
***PUFF!***
it will be safer cause the copper wont burst into shrapnel like cheap nylon does.
NOTE FROM PIMPMANN22: Removed sexual remarks both because they arent neccesary and the post was off topic. Remeber were on a spudding forum... Dont post anything of this nature again.
too bad JOKES arent taken too lightly...
Posted: Fri Feb 17, 2006 6:44 pm
by K40T1C
ok nicholai lets avoid using that kind of term... some ppl get offended by it... further more it is completley irrelevant
Posted: Fri Feb 17, 2006 6:52 pm
by Shrimphead
Agreed. That has gone waaayyyyy to far.
Posted: Fri Feb 17, 2006 7:56 pm
by saladtossser
cardinals08 wrote:why do I need to make a cap? you mean to make the bottom stronger? or to enclose the bottom(some are open on the bottom because some arent spring loaded to push the pop up), because the one I ate is completely closed on the bottom
i get the one where you stick your fingers in.
this might work, but i have very poor eproxy mixing skills.
the one you had can be used too
Posted: Sat Feb 18, 2006 10:31 pm
by guitarfreak
it probably wouldnt hold the pressure. i exclusivley use metal for my pneumatics,i dont even trust pvc!
Posted: Sun Feb 19, 2006 9:55 am
by nicholai
saladtossser wrote:
i get the one where you stick your fingers in.
this might work, but i have very poor eproxy mixing skills.
the one you had can be used too
use putty type epoxy, not the liquid.
its a lot easier to mix than a puddle of goopy stuff. its like mixing black and white play doh to get grey play doh