hey, i know the limit here on the forum is 1/4" steel plate yet but i know that 1" will be taken soon.
i may be able to do 3/4" if i get on team with ragnarok and Larda to make a dart. so i wonder if that would be a world record for a homemade gas powered gun?
it would have been cool to get in guinesse record book with a spud gun and a hole in a 3/4" plate since the hobby may grow then.
ok enough of that i just wanted to talk a little. the thing i was going to ask for was the most impressive shot everybody have ever seen and heard of so i can send a letter to the guinesse and ask if it is possible to get in a book for something like that.
i know the braniac dude was there for the fastest shooting with a spray'n'pray and that is where i got the idea.
so what do you think and will someone be up for the challenge if i can't do it? i know larda and killjoy has a big chance to make it.
i have no high hopes for this i just think it will be cool if i get there and show my friends ETC since everybody ask (is it more powerfull than a sling shot?) lol
Posted: Mon Jul 28, 2008 12:00 am
by THUNDERLORD
IDK the record for spuds. Here's a cool vid: http://www.youtube.com/watch?v=tJmAJZn3i8c&NR=1
Orhttp://www.youtube.com/watch?v=tQtNgy_FqVI
Guy says "Did it blow up?" These .50BMG's go through sewer caps like butter.
I read a 5.56mm (.223 remington) will pierce 3/8" plate steel and 7.62Nato (.308winchester) will pierce 1/2".
So 1" penetration or even 1/4" is pretty good IMO.
1" steel penetration seems like cannon scale compared to that though!
...ok enough of that i just wanted to talk a little...
Go for Guiness or just Ripley's is possible. Just a little "Talk" 8)
Posted: Mon Jul 28, 2008 12:02 am
by frankrede
If you set that record spudfarm, I will have to beat it.
I'm sure FEAR could break it with a proper sabot and ammo.
Posted: Mon Jul 28, 2008 12:10 am
by SpudFarm
[youtube][/youtube]
that video shows the power of a .50.
i hope someone can get through 3/4" plate soon. i have broken the energy levels of a .50 now but the projectile will be hard to make.
i leave that to larda:P
Posted: Mon Jul 28, 2008 12:34 am
by jackssmirkingrevenge
If you really want to make an impression, find a derelict APC and go through the side armour, usually around half an inch or so.
Posted: Mon Jul 28, 2008 12:42 am
by SpudFarm
i have a 1/2" hardened steel plate now.. it would not be to easy to find a defect tank around here (tank? :S )
mabe i should just max it out with a thin tungsten penetrator and try 1" i did 1/4" with a pretty fat penetrator at 3x so a hard tungsten dart that has 4times as high pressure should go through 1"
Posted: Mon Jul 28, 2008 12:56 am
by mobile chernobyl
Are you going for KE rounds like a Saboted tungsten dart for the record, or would you allow a HEAT style projectile. Oh wait I don't think talk of that matter is allowed on here is it?
Posted: Mon Jul 28, 2008 1:12 am
by SpudFarm
i can tell how i see the round infront of my eyes..
it is a 7mm thick 10cm long tungsten penetrator with a perfect angle for penetration. it has no fins it just sits in a 2" long 4.2cm wide teflon case and is going to be fired at point blank at a 11x mix on a 1" or 3/4" plate with a 1/2" plate as a backstop to look if it still had some energy left.
got it?
Posted: Mon Jul 28, 2008 1:13 am
by THUNDERLORD
SpudFarm wrote:...that video shows the power of a .50...
Some guys have all the luck!
But, $7.00+ per round...I'd ask for my money back on the one that got stuck! 8)
Those guys should watch out for riccochets.
Scariest plinking of my life, when I shot a tree with a black powder revolver and saw a gray streak flying back. So I turned my face very quick and saw the bullet hit my friends shirt sleeve. WHOOSH! I thought it went through his arm but it was only the shirt sleeve!
Posted: Mon Jul 28, 2008 1:17 am
by SpudFarm
i am going to say one more thing about .50 before we cut it out
the hardened steel tracer rounds i shot with is $83 per round!
Posted: Mon Jul 28, 2008 2:47 am
by Hotwired
mobile chernobyl wrote:Are you going for KE rounds like a Saboted tungsten dart for the record, or would you allow a HEAT style projectile. Oh wait I don't think talk of that matter is allowed on here is it?
I think not, besides that would have bugger-all to do with the cannon and everything to do with the fact you chucked a shaped charge at the target
SpudFarm wrote:a 1/2" hardened steel plate
I won't hold my breath for that to get a hole in it. But still, hardened could be anything.
SpudFarm wrote:$83 per round!
Haha $415 to fire a 5 round magazine
Posted: Mon Jul 28, 2008 2:59 am
by SpudMonster
THUNDERLORD wrote:
SpudFarm wrote:...that video shows the power of a .50...
Some guys have all the luck!
But, $7.00+ per round...I'd ask for my money back on the one that got stuck! 8)
Those guys should watch out for riccochets.
Scariest plinking of my life, when I shot a tree with a black powder revolver and saw a gray streak flying back. So I turned my face very quick and saw the bullet hit my friends shirt sleeve. WHOOSH! I thought it went through his arm but it was only the shirt sleeve!
[youtube][/youtube]
Posted: Mon Jul 28, 2008 4:26 am
by SpudFarm
the 1/2" will be a easy target on 11x since i got through 1/4" stainless on 3x.
and stop talking about .50's
Posted: Mon Jul 28, 2008 4:27 am
by SpudFarm
the 1/2" will be a easy target on 11x since i got through 1/4" stainless on 3x.
and stop talking about .50's
Posted: Mon Jul 28, 2008 10:14 am
by brogdenlaxmiddie
So did you decide on using a sandbox backstop or not?