Page 55 of 101
Posted: Thu Sep 19, 2013 12:22 pm
by wyz2285
I tried to change the gears on my lathe to cut thread. After some careful dismounting and mounting, I found out I had no idea what I was doing
Somebody please help,
Posted: Thu Sep 19, 2013 12:39 pm
by Labtecpower
Wait,
plastic gears?
For cutting threads the carriage needs to move pretty far with each rotation of the chuck, so I guess you need to mount a larger primary and smaller secondary gear
Posted: Thu Sep 19, 2013 1:07 pm
by wyz2285
Wait, plastic gears?
Yeah... At least some of them.
They sell metal gear set for replacement for around 50 euro, I may buy them but so far the plastic gears have shown no wear so I'm not in a hurry
Posted: Fri Oct 04, 2013 3:18 am
by Talk
I'm getting an error message about the barrel i can't increase the size of barrel because a lot of compressed air will be wasted...
And the Valve Data and Valve Data (cont) are not appropriate can any one tell me the values of a Blower Gun and Pressure Washer gun both?
Re: Short question topic
Posted: Wed Oct 09, 2013 8:19 am
by wyz2285
What short of ignition should I use for a candy rocket? I need something simple so I can explain to my classmates who are not interested at all and hopefully does not involve high voltage...
Re: Short question topic
Posted: Wed Oct 09, 2013 8:28 am
by jackssmirkingrevenge
match heads and a small length of nichrome wire, even a 9V battery will do it.
Re: Short question topic
Posted: Wed Oct 09, 2013 8:45 am
by Labtecpower
I only make black powder rockets, I use fuses for ignition.
Simple and reliable
Re: Short question topic
Posted: Wed Oct 09, 2013 5:26 pm
by wyz2285
Nichrome it is then.
I'd use a fuse if it's just for me to launch, but as it's for others to watch as well I need at least a push buttom
Re: Short question topic
Posted: Wed Oct 16, 2013 3:53 pm
by dart guy
I would like to know how to get the special software GGDT because i REALLY want it but nobody will tell me how to get it
Re: Short question topic
Posted: Wed Oct 16, 2013 4:29 pm
by jrrdw
dart guy wrote:I would like to know how to get the special software GGDT because i REALLY want it but nobody will tell me how to get it
http://www.spudfiles.com/announces/topic13096.html
http://www.thehalls-in-bfe.com/GGDT/index.html
I've given you the top link in a different thread, the tool link is on that page under the heading 'Design'!
The 2nd link is the insulation page,
read it carefully so you don't need to make 10 more post asking how...
Re: Short question topic
Posted: Thu Oct 31, 2013 3:45 am
by wyz2285
Anybody knows what's the difference between the co2 and the green gas magazine for WE open bolt M4/scar?
The co2 cost 10 euro more than the green gas ones and only work after I raise the pressure pass 800 psi. The propane's max pressure is below 200 psi, how will the green gas mag work??
Edit:
Check this out!
http://answers.yahoo.com/question/index ... 100AA3c9yl
The guy said green gas(propane) is much more powerful than co2, LOL
Re: Short question topic
Posted: Thu Oct 31, 2013 4:24 am
by Zeus
Well besides the obvious? What differences do you want or need? For running HPA into it I'd recommend Green Gas, so you can run 50-160PSI, which I assume is easier to get with regulators. Also if you sell it to someone with a CO2 rig instead, they can use a more common regulator.
Regarding suggestions too, my mate just bought a 1200rd motorised bitch bucket (hicap), any chance you could make a converted version with one of those? If you can, I can get a bit of business through me.
Re: Short question topic
Posted: Thu Oct 31, 2013 6:22 am
by wyz2285
8) Ahah, right on time. I've just managed a way to convert a drum mag+gas mag combo
Gottcha, the advantage of a co2 it's just that you can use standard paintaball tank reg.
Re: Short question topic
Posted: Thu Oct 31, 2013 2:45 pm
by dart guy
got more problems i keep getting error 339; missing files.
gddt will not work.
Re: Short question topic
Posted: Thu Oct 31, 2013 3:23 pm
by jrrdw
dart guy wrote:got more problems i keep getting error 339; missing files.
gddt will not work.
Works just fine if you have the files you need...Google is your friend. I bet it's a missing .ocx or .ocs I forget.