Search found 361 matches
- Sat Oct 12, 2013 3:35 am
- Forum: Pneumatic Cannons
- Topic: Need some advise
- Replies: 5
- Views: 1799
Re: Need some advise
Yea, it looks like a compression tee but without the fittings and the brass rings on it. For comparison, a fully equipped compression tee.... http://www.wickes.co.uk/content/ebiz/wickes/invt/420205/Compression-Equal-Tee_large.jpg You have to keep in mind that you need a good surface inside the tee t...
- Sat Oct 12, 2013 2:22 am
- Forum: Pneumatic Cannons
- Topic: Need some advise
- Replies: 5
- Views: 1799
Re: Need some advise
1/2" is small to begin with so I would take a "compression tee" if you mean a tee with a smooth inside and outer threads. edit: Sorry, I looked up compression tee and I don't think it will fit your needs. Find a tee with outer threads and a smooth surface inside or a tee with inner threads + 1/2" ma...
- Sat Oct 12, 2013 1:58 am
- Forum: Off-Topic Hobbies
- Topic: YouTube comments (FAIL)
- Replies: 35
- Views: 10415
Re: YouTube comments (FAIL)
Some people don't understand piston valves hahaha. MRR, you were actually the person who taught me how one works :lol: you proceeded to refer me here because you didn't want to answer any more questions :D that was like 3 years ago... I still give tips and tricks to people that ask politely, but in...
- Fri Oct 11, 2013 1:49 pm
- Forum: Off-Topic Hobbies
- Topic: YouTube comments (FAIL)
- Replies: 35
- Views: 10415
Re: YouTube comments (FAIL)
This comment actually made me laugh
Apparently he doesn't understand the concept of piston valves.
=> trigger = ball valve
Apparently he doesn't understand the concept of piston valves.
=> trigger = ball valve
- Sat Feb 23, 2013 12:50 pm
- Forum: General How-To & Discussion
- Topic: DIY 3/2 DCV (video)
- Replies: 62
- Views: 46243
- Fri Feb 22, 2013 12:18 pm
- Forum: General How-To & Discussion
- Topic: DIY 3/2 DCV (video)
- Replies: 62
- Views: 46243
- Wed Feb 20, 2013 1:39 pm
- Forum: General How-To & Discussion
- Topic: DIY 3/2 DCV (video)
- Replies: 62
- Views: 46243
- Thu Feb 14, 2013 7:28 am
- Forum: General How-To & Discussion
- Topic: DIY 3/2 DCV (video)
- Replies: 62
- Views: 46243
- Wed Feb 13, 2013 5:43 pm
- Forum: Pneumatic Cannons
- Topic: GGDT isn't showing the same velocities I get with a chrono
- Replies: 9
- Views: 3107
- Wed Feb 13, 2013 5:09 pm
- Forum: General How-To & Discussion
- Topic: How to determine projectile velocity with a phone book
- Replies: 49
- Views: 12107
This ought to be a follow up but the user I was talking about is a fellow spudfiles user.
Look at his post here:
http://www.spudfiles.com/forums/ggdt-is ... 24963.html
Look at his post here:
http://www.spudfiles.com/forums/ggdt-is ... 24963.html
- Tue Feb 12, 2013 5:44 pm
- Forum: Ammo & Parts
- Topic: What did i just buy?
- Replies: 28
- Views: 9773
you'll need to loop the pilot into the middlesection for it to pop open .. Or..take out the bottom center O-ring and THEN plug the side. It doesn't look like it is necessary to pressurize the middle section. If you use a 3-way valve on the pilot and loop it to the chamber, it would work like a cham...
- Tue Feb 12, 2013 1:08 pm
- Forum: Ammo & Parts
- Topic: What did i just buy?
- Replies: 28
- Views: 9773
- Tue Feb 12, 2013 10:25 am
- Forum: Pneumatic Cannons
- Topic: WIP- piston-reservoir
- Replies: 3
- Views: 1270
- Tue Jan 22, 2013 4:56 pm
- Forum: Pneumatic Cannons
- Topic: Help with piston in coaxial QEV (never encountered this b4)
- Replies: 14
- Views: 4498
- Sat Jan 19, 2013 5:32 pm
- Forum: Hybrid Cannons
- Topic: cup shaped bursk disk
- Replies: 12
- Views: 4525
ok im thinking of a cup shaped piston /burst disk machined out of delrin or something or made by deep drawing with vacuum out of some sort thermoplastic Ok, I get it now, the OP was a little misleading though (I had a piston hybrid in mind). ... Wouldn't machined burst disks be too expensive if you...