Difference between revisions of "Hybrid cannon"

 
(29 intermediate revisions by 15 users not shown)
Line 1: Line 1:
 +
[[Image:hybrid.jpg|right|thumb|300px| A very well built hybrid, although it is not safe for handheld operation due to its use of a PVC chamber]]
 +
A '''hybrid''' is a type of spudgun that combines principles of the [[combustion cannon|combustion]] and [[pneumatic cannon|pneumatic]] spudgun. It uses a pressurized mixture of [[fuel]] and air to get more power out of a given chamber volume than a normal combustion or pneumatic gun could.
 +
The hybrid is capable of higher velocities than a combustion or pneumatic spudgun; projectiles fired by a hybrid have reached almost 1000 m/s. This is possible because of the higher [[pressure]] gases generated by a hybrid [[combustion process|combustion]].
 +
 
A hybrid launcher consists of seven basic elements:
 
A hybrid launcher consists of seven basic elements:
  
*High pressure combustion chamber
+
*High pressure combustion [[chamber]]
*Pressure-triggered main valve (usually a [[burst disk]])
+
*Pressure-triggered main [[valve]] (usually a [[burst disk]], see below)
 
*[[Barrel]]
 
*[[Barrel]]
*Fuel system (usually [[metered propane]])
+
*Fuel system (usually [[fuel meter|metered propane]])
*Air filling valve
+
*Inlet port for propellant mix with a connection for attaching fueling line(s)(usually [[schrader valve|schrader]] or [[quick disconnect|quick connect]])
*Ignition source
+
*High-voltage [[Ignition source]]
*One or more pressure gauges
+
*One or more [[pressure gauge]]s
 +
 
 +
==Operation theory==
 +
A hybrid is first injected with a measured amount of fuel - much more than would be used in a regular combustion. However, without adequate oxygen, the mixture would be far too rich to ignite, so the chamber is then with pressurized air. The amount of air depends on how much fuel was added, and is calculated to achieve a [[stoichiometric]] fuel/air ratio in the chamber.
 +
 
 +
A hybrid using twice as much fuel and air as a comparable combustion gun is said to be using a 2X mix. Higher mixtures can be used and will produce even higher pressures. The fuel and air needs to be measured and matched carefully to ensure reliable operation, pressure gauges and fuel [[fuel meter|meters]] are used for this.
  
A hybrid is a type of spudgun that combines principles of the combustion and pneumatic spudgun. It uses a pressurized mixture of fuel and air to get more power out of a given chamber volume. In order to fire, the operator first inserts a [[burst disk]], usually consisting of aluminium foil or plastic, between the chamber and barrel. A cam coupling or union is used to hold the burst disk in place. The operator then loads projectile into the barrel, adds fuel to the combustion chamber, and then adds pressurized air. The amount of air depends on how much fuel was added, and is calculated to achieve a stoichiometric fuel/air ratio in the chamber. when the ignition source is triggered, the pressure from the combustion ruptures the burst disk and propels the projectile out of the barrel. The hybrid is capable of higher velocities than a combustion or pneumatic spudgun, projectiles fired by a hybrid have broken the sound barrier (Source). A hybrid using twice as much fuel and air as a comparable combustion gun is said to be using a 2X mix, higher mixtures can be used and will produce even higher pressures. The fuel and air needs to be measured and matched carefully to ensure reliable operation, pressure gauges and fuel meters are used for this. A pressure gauge with a check valve can also be added to record the peak chamber pressure of the gun.
+
The ignition of a hybrid gun is more difficult than a normal combustion, as the length of a spark is roughly inversely proportional to the density of the gas. This necessitates the use of high-powered [[ignition source]] such as a [[stungun]], [[flyback circuit]], or other high-voltage source; [[BBQ ignitor|grill igniters]] may be unreliable and require a very small [[spark gap]](typically 1mm or less) to work correctly in pressurized fuel/air environments.  
  
 +
The gases resulting from the combustion of the fuel/air mixture are released to the barrel via a self-operating valve of some sort, most commonly a [[burst disk]] because of it's simplicity and reliability, although self-venting [[piston valve|piston]]/[[diaphragm valve|diaphragm]] valves have been used. The valve is required to contain the pressure of the mixture pre-ignition, in other words, to prevent the pressurized fuel/air mixture from exiting out the barrel before ignition. Upon ignition of the fuel-air mix, the pressure rises and the valve opens.
  
SAFETY: A hybrid is the most dangerous launcher that can be built. It is advised to build with pipe that can handle the high pressure environment (200+ PSI) such as Sch. 80 PVC or metal. Remote ignition is a must, and the limit of a 4x propane/ 4 atmosphere mix should never be breached. If a higher mix is attempted, DDT (deflagration to detonation transition) can occur, causing an extreme pressure spike. Most pipe cannot handle the spike, and will shatter, launching plastic shards every where. Therefore utmost care must be taken with these launchers.
+
===Safety===
 +
A hybrid is one of the more dangerous types of launchers to build, apart from high pressure pneumatics. It is advised to only attempt to build one with pipe that can handle the high pressure environment (300+ [[Pressure gauge|PSI]]), generally SCH 40 steel or better. SCH 80 PVC has been used, but is not safe due to recurring fatiguing problems that have been observed in PVC hybrids and multiple failures even at low mixes. As with any launcher, the entire chamber is only rated to the spec of the lowest-rated part, so care must be taken when constructing the chamber of a hybrid. [[Remotely_activated_valve |Remote ignition]] is a must if PVC is used as a construction material, and is strongly advised for the initial testing of any hybrid. Although it was originally thought that mixes higher than 4x posed an unacceptable risk of [[DDT]] (deflagration to detonation transition), further calculations have revealed that the increased temperature of higher mixes barely counters the decreased burn rate caused by higher pre-ignition pressures, and that even a 20x mix will only burn a few m/s faster than a 1x mix. If DDT of all or most of the fuel load did occur, it would produce an extremely violent shock and pressure spike, which would cause any PVC chamber to rupture, and damage steel or copper components which were not highly overbuilt. The standard for hybrid construction is currently SCH 40 [[Steel Pipe|steel pipe]] and fittings, which have been tested in 2" sizes at mixes of up to 20x, repeatedly without failure. Theoretical burst pressure of SCH 40 2" steel pipe is >4kpsi (ignoring threaded sections and end effects), and there is no recorded incidence of ruptures occurring in SCH 40 steel hybrid chambers. Copper tube barrels have burst and/or bulged due to what is thought to be localized DDT.

Latest revision as of 17:05, 14 May 2012

A very well built hybrid, although it is not safe for handheld operation due to its use of a PVC chamber

A hybrid is a type of spudgun that combines principles of the combustion and pneumatic spudgun. It uses a pressurized mixture of fuel and air to get more power out of a given chamber volume than a normal combustion or pneumatic gun could. The hybrid is capable of higher velocities than a combustion or pneumatic spudgun; projectiles fired by a hybrid have reached almost 1000 m/s. This is possible because of the higher pressure gases generated by a hybrid combustion.

A hybrid launcher consists of seven basic elements:

Operation theory

A hybrid is first injected with a measured amount of fuel - much more than would be used in a regular combustion. However, without adequate oxygen, the mixture would be far too rich to ignite, so the chamber is then with pressurized air. The amount of air depends on how much fuel was added, and is calculated to achieve a stoichiometric fuel/air ratio in the chamber.

A hybrid using twice as much fuel and air as a comparable combustion gun is said to be using a 2X mix. Higher mixtures can be used and will produce even higher pressures. The fuel and air needs to be measured and matched carefully to ensure reliable operation, pressure gauges and fuel meters are used for this.

The ignition of a hybrid gun is more difficult than a normal combustion, as the length of a spark is roughly inversely proportional to the density of the gas. This necessitates the use of high-powered ignition source such as a stungun, flyback circuit, or other high-voltage source; grill igniters may be unreliable and require a very small spark gap(typically 1mm or less) to work correctly in pressurized fuel/air environments.

The gases resulting from the combustion of the fuel/air mixture are released to the barrel via a self-operating valve of some sort, most commonly a burst disk because of it's simplicity and reliability, although self-venting piston/diaphragm valves have been used. The valve is required to contain the pressure of the mixture pre-ignition, in other words, to prevent the pressurized fuel/air mixture from exiting out the barrel before ignition. Upon ignition of the fuel-air mix, the pressure rises and the valve opens.

Safety

A hybrid is one of the more dangerous types of launchers to build, apart from high pressure pneumatics. It is advised to only attempt to build one with pipe that can handle the high pressure environment (300+ PSI), generally SCH 40 steel or better. SCH 80 PVC has been used, but is not safe due to recurring fatiguing problems that have been observed in PVC hybrids and multiple failures even at low mixes. As with any launcher, the entire chamber is only rated to the spec of the lowest-rated part, so care must be taken when constructing the chamber of a hybrid. Remote ignition is a must if PVC is used as a construction material, and is strongly advised for the initial testing of any hybrid. Although it was originally thought that mixes higher than 4x posed an unacceptable risk of DDT (deflagration to detonation transition), further calculations have revealed that the increased temperature of higher mixes barely counters the decreased burn rate caused by higher pre-ignition pressures, and that even a 20x mix will only burn a few m/s faster than a 1x mix. If DDT of all or most of the fuel load did occur, it would produce an extremely violent shock and pressure spike, which would cause any PVC chamber to rupture, and damage steel or copper components which were not highly overbuilt. The standard for hybrid construction is currently SCH 40 steel pipe and fittings, which have been tested in 2" sizes at mixes of up to 20x, repeatedly without failure. Theoretical burst pressure of SCH 40 2" steel pipe is >4kpsi (ignoring threaded sections and end effects), and there is no recorded incidence of ruptures occurring in SCH 40 steel hybrid chambers. Copper tube barrels have burst and/or bulged due to what is thought to be localized DDT.