darts for pneumatics
Posted: Wed Dec 28, 2005 6:11 am
i have been trying to find a good acurate dart ammo ive tried scewers metal wire and other things do you have any ideas. 
Page 1 of 2
Posted: Wed Dec 28, 2005 6:25 am
I have some ideas for sabot darts for a 3/4 barrel. I'm working on the renders, but im not quite sure when they'll be done. I'll post em as soon as possible.
Posted: Wed Dec 28, 2005 2:30 pm
You can adapt the nail to fit your barrel with tape. That's the easiest way.
Posted: Wed Dec 28, 2005 3:12 pm
http://www.tomshiro.org/pdart/primer.html that might work you could experiment with diffrent things for cones like copper and cardboard.
Posted: Wed Dec 28, 2005 4:54 pm
roll paper like that and put a bamboo skewer thru that 
Posted: Thu Dec 29, 2005 5:22 am
yeah i have a home made blow gun and have tried the bamboo skewers in the cannon but they seem to be a bit light so im trying to find a metal alternative tnxs for the help.
Posted: Thu Dec 29, 2005 4:02 pm
1/4 penny nails work pretty well for darts, at least from a blowgun; 1/16" diameter, 1.75" long (going on memory there). Cheap too. You should be able to buy them at any self-respecting hardware store.
But thanks for the reminder. I think I'll go roll a dart or two for my 1" barrel.
But thanks for the reminder. I think I'll go roll a dart or two for my 1" barrel.
Posted: Tue Jan 03, 2006 2:43 am
tnxs for the info
Posted: Tue Jan 03, 2006 7:23 am
ok i just found the greatest thing for 1/2"barrels
take a piece of 1/2"dowel and cut about half an inch off, then drill a small hole in the middle. put a long screw through. suprisingly they fly really straight and have good penetration
take a piece of 1/2"dowel and cut about half an inch off, then drill a small hole in the middle. put a long screw through. suprisingly they fly really straight and have good penetration
Posted: Thu Jan 05, 2006 8:54 pm
ok this is what i do in my spare time:
you all know pen guns right?(those pen tubes with a rubber band tied on one end of it and you fire pen inks)well we used to fire coathanger ammo out of that but you can also use in for a mini spud gun i suppose.
you get a metal coathanger and cut out straight bits off the wire. i usually cut it 9 inch for each peice and that gives me three peices from one coathanger. REMEMBER you cant use the curved bits on the coathanger. i then put a peice in a vice and sharpen one end of the coathanger using a file.
we fired one of these at school out of a pen gun 10 feet away from a black board and it went through the blackboard!!!!!!!!!BE VERY CAREFULL this is a killing dart never point it at someone!!!!!!!!
happy shooting!!!!!!
you all know pen guns right?(those pen tubes with a rubber band tied on one end of it and you fire pen inks)well we used to fire coathanger ammo out of that but you can also use in for a mini spud gun i suppose.
you get a metal coathanger and cut out straight bits off the wire. i usually cut it 9 inch for each peice and that gives me three peices from one coathanger. REMEMBER you cant use the curved bits on the coathanger. i then put a peice in a vice and sharpen one end of the coathanger using a file.
we fired one of these at school out of a pen gun 10 feet away from a black board and it went through the blackboard!!!!!!!!!BE VERY CAREFULL this is a killing dart never point it at someone!!!!!!!!
happy shooting!!!!!!
Posted: Sat Jan 07, 2006 1:28 pm
that is a really good idea. i make pen guns..... wow...
Posted: Sat Jan 07, 2006 5:10 pm
i made some thing like that for my blow gun and i am going to use the same idea as that for my pneumatic rifle.
Posted: Mon Jan 23, 2006 4:58 pm
use a lathe for darts
Posted: Mon Jan 23, 2006 5:21 pm
why would you use a lathe 
and if you did use a lathe what part of the dart would you use it for or are you saying to get a lump of steel and shave it down until its perfect in that case it is way to much work for just one dart.
and if you did use a lathe what part of the dart would you use it for or are you saying to get a lump of steel and shave it down until its perfect in that case it is way to much work for just one dart.Posted: Thu Jul 10, 2008 10:07 pm
I've only made a few darts, as they seemed to consume more time and money than they were worth, but here they are:
50mm.
And the more sturdily built 75mm version. I've never used any one launcher long enough to develop a dart design to completion, mostly because I never felt I had enough available power to make it worthwhile. Now, however...
50mm.
And the more sturdily built 75mm version. I've never used any one launcher long enough to develop a dart design to completion, mostly because I never felt I had enough available power to make it worthwhile. Now, however...