Meh, what do i know!? Best wait for the experts to reply
Small coaxial
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
Seems a bit short to me, however not having completed a pneumo it may work fine. I just tend to think it *might* have troubles sliding freely.
Meh, what do i know!? Best wait for the experts to reply
Meh, what do i know!? Best wait for the experts to reply
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
May have found something even better.
See image. b is 52.9mm, c is 55mm
Perfect width, and length!
http://www.hansenproducts.co.nz/product ... s/SMHT.jpg
I'd have to chop the thread off though
See image. b is 52.9mm, c is 55mm
Perfect width, and length!
http://www.hansenproducts.co.nz/product ... s/SMHT.jpg
I'd have to chop the thread off though
- Attachments
-
- smht_dimen copy.jpg (17.24 KiB) Viewed 2744 times
Last edited by rixth on Sat Oct 27, 2007 6:12 am, edited 1 time in total.
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
Now that sounds like the go
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
I swear to God I'm going to kill someone....
I'm going MENTAL. I can't get the barrel to seal (yes this is my first piston valve)...
I've tried a couple different pistons, as well as trying putting fabric or a disk of hot glue behind it (as in http://www.spudfiles.com/forums/files/untitled2_531.jpg). Whenever I pump, air just escapes out the barrel. I've tried manually pressing the piston up against the barrel, then filling it but it still escapes.
The sealing face is a disc cut out of a neoprene gumboot (for you yanks, this is what a gumboot is: http://en.wikipedia.org/wiki/Image:Wellies.jpg ). It's maybe 2mm (0.07in) thick.
I'm going MENTAL. I can't get the barrel to seal (yes this is my first piston valve)...
I've tried a couple different pistons, as well as trying putting fabric or a disk of hot glue behind it (as in http://www.spudfiles.com/forums/files/untitled2_531.jpg). Whenever I pump, air just escapes out the barrel. I've tried manually pressing the piston up against the barrel, then filling it but it still escapes.
The sealing face is a disc cut out of a neoprene gumboot (for you yanks, this is what a gumboot is: http://en.wikipedia.org/wiki/Image:Wellies.jpg ). It's maybe 2mm (0.07in) thick.
Hmm thats a tough one mate but I reckon the face on the barrel might be abit wonky. That was the problem I had. Just place some fine wet n dry sandpaper down on a table and rub the face against it. That should smooth out any irregularities.
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
It may be that the gumboot material is too hard. Try a different kind of rubber.
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
One of the best sources of rubber is a car or bicycle inner tube, I'm sure you can easily get your hands on one.
Also, make sure that the sealing end of your barrel is 100% flat, smooth and parallel to the sealing face of your piston.
Also, make sure that the sealing end of your barrel is 100% flat, smooth and parallel to the sealing face of your piston.
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
How is the sealing face attached to the piston?
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
Is the piston filled with anything? If not the rubber might be getting pushed into the piston under pressure.
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
is there a washer between the bolt and the rubber?
hectmarr wrote:You have to make many weapons, because this field is long and short life