It should have 3 ports.
In
Out
Pilot.
Air should flow with little to no constriction from the IN port to the OUT port.
When pressure ~= to the Pressure of flow from the IN port is applied to the pilot the valve should close off the IN port stopping flow to the out port.
Pressure from the Pilot Should not leak to the OUT port.
When the pressure in the Pilot port is release the pressure from the IN port should open the valve once again allowing flow with little to no constriction from the IN port to the OUT port.
a globe valve where the plug is pneumatically actuated would be an example of what I'm looking for.
Hunting for a particular Valve
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
it seems that what you want is an air actuated 3 way valve
though I don't get this part
though I don't get this part
Does it have to be equal ? is it crucial ? or is it just I wrote this becauseWhen pressure ~= to the Pressure of flow from the IN port is applied to the pilot the valve should close off the IN port stopping flow to the out port.
I am gonna use air from the tank that is also attached to port IN so I wrote it here without thinking (ie it isn't a real requirement)
Children are the future
unless we stop them now
unless we stop them now
-
- Private 2
- Posts: 21
- Joined: Fri Aug 03, 2012 2:51 pm
it is extremely crucial. the idea is that the valve will both trap the pressure contained downstream from the valve through the OUT port, and will lock the valve preventing flow after that pressure has been released.
step 1 allow air of desired pressure flow through IN port to OUT port.
step 2 allow pressure to build in pilot port from the OUT port.
step 3 allow valvle to close self given that the pressure downstream of OUT port is ~= pressure upstream of IN port and thus pressure behind pilot is also ~= to pressure upstream of IN port.
step 4 fire canon venting pressure downstream of OUT port. pilot port maintains its pressure via check valve.
step 5 reload cannon
step 6 vent pressure behind pilot opening valve.
return to step 1
wituout this valve several problems occur.
1 the canon cannot be reloaded
2 the canon can never completely vent the chamber into the barrel
step 1 allow air of desired pressure flow through IN port to OUT port.
step 2 allow pressure to build in pilot port from the OUT port.
step 3 allow valvle to close self given that the pressure downstream of OUT port is ~= pressure upstream of IN port and thus pressure behind pilot is also ~= to pressure upstream of IN port.
step 4 fire canon venting pressure downstream of OUT port. pilot port maintains its pressure via check valve.
step 5 reload cannon
step 6 vent pressure behind pilot opening valve.
return to step 1
wituout this valve several problems occur.
1 the canon cannot be reloaded
2 the canon can never completely vent the chamber into the barrel
-
- Specialist 3
- Posts: 343
- Joined: Thu Feb 16, 2012 5:23 pm
- Location: Leesburg
- Contact:
Please refrain from talking about hunting, forum rules
Jk
, ok all jokes aside
i dont understand ur question, so is it liek a qev?
Jk

i dont understand ur question, so is it liek a qev?
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
I don't get it. What do you want to achieve with this valve ?it is extremely crucial. the idea is that the valve will both trap the pressure contained downstream from the valve through the OUT port, and will lock the valve preventing flow after that pressure has been released.
Can't you just use a 3 way valve ?
I suspect you don't really need this special valve
this is how this is normally done:

Spend some time analysing it. the main part is the 3 way valve - it first allows filling the chamber and then pilots the QEV and blocks off flow to the chamber at the same time
you can either get a 3 way like the one I used or a slide valve (which is a kind of 3 way valve too) -> here is jsr's thread on it ->
http://www.spudfiles.com/forums/semi-au ... 23626.html
Children are the future
unless we stop them now
unless we stop them now
- jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
sagthegreat wrote:Please refrain from talking about hunting, forum rules



hectmarr wrote:You have to make many weapons, because this field is long and short life
-
- Private 2
- Posts: 21
- Joined: Fri Aug 03, 2012 2:51 pm
Thanks for the replies. but I think I've managed to design a useable valve that will meet my scheme.
wish me luck I'm off to scheme!
wish me luck I'm off to scheme!