Air tank sealing problem.
Apologies. I now see you suggested that the screws were the source of the leaks.
Unless you're using a PVC glue type I'm not familiar with, you're solvent-welding the PVC. This results in an area that is thicker and stronger than the rest of the pipe.
Unless you're using a PVC glue type I'm not familiar with, you're solvent-welding the PVC. This results in an area that is thicker and stronger than the rest of the pipe.
-
- Staff Sergeant 3
- Posts: 1769
- Joined: Mon Mar 21, 2011 5:41 pm
No problem sae. Mark, I really do need better tools, or at least a corded drill...
- Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
id save up and get a really good cordless drill. i have a Dewalt DC988KC-XE, its a beast comes with 3 batterys each one lasts a day most of the time. full charges in about 2hr and its got plenty off power. also come with a the heavy duty steel chuck. its $500 aus but its defiantly worth it.
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
- mark.f
- Sergeant Major 4
- Posts: 3627
- Joined: Sat May 06, 2006 11:18 am
- Location: The Big Steezy
- Has thanked: 52 times
- Been thanked: 53 times
- Contact:
I have your basic 3/8" keyed-chuck corded drill. Plenty of torque for drilling through steel pipe and you don't have to worry as much about your bit slipping around in the chuck as you do with cheaper keyless chucks like you find on some cordless drills.
-
- Staff Sergeant 3
- Posts: 1769
- Joined: Mon Mar 21, 2011 5:41 pm
I need a corded with alot of torque and ajustable speed, or a drill press. Plus I need a air compressor rather than a bike pump...
-
- Staff Sergeant 3
- Posts: 1769
- Joined: Mon Mar 21, 2011 5:41 pm
Too true. My grandfather has a drill press I could use, but I am not sure if he would let me.... EDIT, I discarded the tanks (it was old pvc anyways...) and I rebuilt another... The cement has dried and has no leaks what so ever, and I applyed epoxy over it because I felt double reinforcement was better than 1 layer.
- Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 7 times
Doesn't sound like you gave it much cure time
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
- clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
My glue take 2 hrs to cure according to the can.
- Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 7 times
Same here but I always give it at least a day...
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
- clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
I give it two hours before 30 psi, then 1 day before any more.
-
- Staff Sergeant 3
- Posts: 1769
- Joined: Mon Mar 21, 2011 5:41 pm
Mine is 1 hour... Really good glue too, . I usually put it to 20 psi for now, and after a day or two send it up to past 50.
-
- Staff Sergeant 3
- Posts: 1769
- Joined: Mon Mar 21, 2011 5:41 pm
Well, I figured I would let you guys know... I got a almost brand new empty freeon tank! Very heavy duty... My dad ran by an old friend who owns a auto shop juts around the corner and asking if he had any thing and he said that he had no use for the tank and it was too heavy to recycle (dont see how when they simply melt it down...). High pressure tank, about 300 - 600 psi or something close to that. It came off a freeon recovery unit for a car, which means it pulled the freeon that was charged up. Its built to last and hold pressure! No need for my crappy pvc air tank anymore...
- Technician1002
- Captain
- Posts: 5189
- Joined: Sat Apr 04, 2009 11:10 am
Just a quick note on the Freon Recovery tanks. Because they are refillable as opposed to the disposable tanks, they are much heavier.
If you intend to do any welding on it, you will find it has lots of oil residue. Watch for build up of explosive oil fumes if welding. Either fill the tank with water first or run a constant inert gas in the tank to keep Oxygen out. Argon, Nitrogen, or CO2 work for the purge gas. Don't use compressed air.
The tank may have been disposed of due to the 3 year recertification required. Check the manufacture date. Is it older than 3 years? If it is older than 3 years, does it have a newer date stamped in the metal near the valve? Is that date older than 3 years?
If the tank is expired, don't plan on exceeding 300 PSI with it. If you weld on it, limit is 1/2ed.
If you intend to do any welding on it, you will find it has lots of oil residue. Watch for build up of explosive oil fumes if welding. Either fill the tank with water first or run a constant inert gas in the tank to keep Oxygen out. Argon, Nitrogen, or CO2 work for the purge gas. Don't use compressed air.
The tank may have been disposed of due to the 3 year recertification required. Check the manufacture date. Is it older than 3 years? If it is older than 3 years, does it have a newer date stamped in the metal near the valve? Is that date older than 3 years?
If the tank is expired, don't plan on exceeding 300 PSI with it. If you weld on it, limit is 1/2ed.