Tutorial - Making a small o ringed piston on a drill press

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
User avatar
saefroch
Staff Sergeant 2
Staff Sergeant 2
Posts: 1679
Joined: Mon Jun 08, 2009 8:47 am
Location: U.S.A.- See Map

Tue Nov 30, 2010 7:37 pm

frocksie wrote:Of course, I had access to a lathe, so I was able to machine clean faces. That being said, it would be worth a shot, as if there is no rubber sealing face, it can never be blown out the barrel!
No precision machining needed. I cut a section of UHMWPE with a hacksaw blade on a drill press, then when the seal blew off once, it sealed anyway. Only trouble is that it didn't pilot, since the entire front of it was sealed to the port and my check valve wasn't fully working yet.
User avatar
Matt_NZ
Private 4
Private 4
Posts: 65
Joined: Fri Apr 09, 2010 4:42 am

Tue Nov 30, 2010 7:58 pm

Oxbreath wrote: I have been considering it.
Same. There is a wide range on eBay, but they charge alot to post to NZ. I'm also looking for a quite a large piece (2.5").

Another idea I had was to buy a cheap plastic chopping board then use tech's technique to get your designated size.
User avatar
Technician1002
Captain
Captain
Posts: 5189
Joined: Sat Apr 04, 2009 11:10 am

Tue Nov 30, 2010 9:06 pm

Matt_NZ wrote: The same stuff milk jugs are made of.
I wonder if anyone has tried molding a milk jug to make a block of HDPE?
I tried it and it didn't work very well. Milk jugs have some kind of mold release contaminate on the surface, so even though it melts, the resulting rubbery goo does not flow into a solid mass, but instead is full of cracks holes and such.

If you look at the plastic planking made from used shopping bags and recycled plastic, you get about the same result. It does not turn into a nice solid chunk of plastic.

Look up "Recycled Plastic Lumber" to see what the stuff will be like. It's OK for a park bench or decking, but lousy for building pistons.

http://www.theparkcatalog.com/itemdesc. ... ce=Froogle

EDIT;

Molten HDPE can best be described as having the consistancy of a cross of melted cheeze and gummy bears. It feels like rubber much like gummy bears. You need to get it up to about 375-425 degrees F do do this. You won't want to touch it with your bare hands. The stuff is hot when melted.

They will squish together with lots of pressure, but they won't become a solid mass simply by putting a bunch in a jar. I used clamps to laminate the piston. Simply stacking the melted faces toghther does not work. Melting a bunch of cut up milk cartons provides the same poor results.
User avatar
Matt_NZ
Private 4
Private 4
Posts: 65
Joined: Fri Apr 09, 2010 4:42 am

Wed Dec 01, 2010 12:14 am

Technician1002 wrote: You need to get it up to about 375-425 degrees F to do this...

They will squish together with lots of pressure, but they won't become a solid mass simply by putting a bunch in a jar. I used clamps to laminate the piston.
Ok , so when you melted this stuff with your custom thermostatically controlled heating unit, would it not just stick to the pan?
User avatar
Technician1002
Captain
Captain
Posts: 5189
Joined: Sat Apr 04, 2009 11:10 am

Wed Dec 01, 2010 12:43 am

It did melt and stick to the pan. That is why I used a custom heating unit from Goodwill instead of using one from the kitchen. This removed some of the surfaces contaminates from the plastic surface as well as adding some of the Teflon non stick surface to the plastic. You can see the contamination on my finished piston. Getting the plastic to fuse to plastic required the squish, other wise very little of the surfaces bond well and can be snapped apart when cooled.

I think it was JSR who laminated some the other direction and air pressure seperated the layers of his piston because the bonding was poor. I feared this in my piston so I laminated in the other direction so air pressure hold the piston together instead of ripping it apart.

I can't find the photo of the broken piston at the moment.

Edit;

Found the post.. It was Ranger.. I got JSR from the following post in that thread. Still makes me smile.
I make these pistons by cutting 2" circular holes with a holesaw in a cutting board and then heat them up and press them together. Then turn them down on a drill press. I guess when I heated and pressed them together, I didnt do it good enough.
Image
User avatar
Matt_NZ
Private 4
Private 4
Posts: 65
Joined: Fri Apr 09, 2010 4:42 am

Wed Dec 01, 2010 2:33 am

I make these pistons by cutting 2" circular holes with a holesaw in a cutting board and then heat them up and press them together. Then turn them down on a drill press. I guess when I heated and pressed them together, I didnt do it good enough.

:D :D I'll do my best not to turn up like this guy.

Lucky enough, I've got an old "custom thermostatically controlled heating unit" in the garage. Lets see how this turns out. 8)
Selador
Specialist 2
Specialist 2
Posts: 213
Joined: Wed Nov 03, 2010 9:44 pm

Wed Dec 01, 2010 2:10 pm

There must be -some- way to melt milk jugs together, consistantly.

A few years ago, I saw a program that devoted some time to how some people in India, or Pakistan, or somewhere else in that region... Were making prosthetic limbs from old milk jugs.

They actually showed part of the process.

I believe they added some chemical to it, like acetone or MEK.

They made a 'soup' of the plastic, (actually showed them stirring it up), then poured that into a mold.

I have been googling to try to find the info, but so far have been unsuccessful.
If you can't fix it, you don't own it.
cannon monkey
Specialist 3
Specialist 3
Posts: 399
Joined: Sun Sep 07, 2008 10:50 am
Location: usa FL

Mon Feb 07, 2011 11:31 pm

where can i find this UMWHDPE or HDPE stuff? looking to make a 2 inch piston
most big random like i ever seen
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Mon Feb 07, 2011 11:49 pm

Technician1002 wrote:I think it was JSR who laminated some the other direction and air pressure seperated the layers of his piston because the bonding was poor. I feared this in my piston so I laminated in the other direction so air pressure hold the piston together instead of ripping it apart.

I can't find the photo of the broken piston at the moment.

Edit;

Found the post.. It was Ranger.. I got JSR from the following post in that thread. Still makes me smile.
JSR would have just cast it out of epoxy, but thank you for automatically associating him with FAIL :D
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
Technician1002
Captain
Captain
Posts: 5189
Joined: Sat Apr 04, 2009 11:10 am

Tue Feb 08, 2011 2:21 am

Sorry JSR.. :oops:

@ cannon monkey, HDPE rod and sheets can be purchased from any good plastics supplier. I used Tap Plastics.

Many white cutting boards are made of HDPE.

http://www.tapplastics.com/shop/category.php?bid=39&

McMaster-Carr has HDPE rod. Here it is in 2 inch.
http://www.mcmaster.com/#plastics/=axu5j9
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Tue Feb 08, 2011 2:24 am

Technician1002 wrote:Sorry JSR.. :oops:
No need, anyone who refers to himself in the third person deserves some level of mockery :D
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
wyz2285
First Sergeant 2
First Sergeant 2
Austria
Posts: 2385
Joined: Sat Mar 06, 2010 7:50 am
Location: Porto, Portugal
Has thanked: 1 time
Been thanked: 3 times
Contact:

Tue Mar 27, 2012 4:24 am

I made a video about this "how to" :)
[youtube][/youtube]
Oh, and I made a chamber seal piston valve repeater 8)
Sorry for bumping this thread but I thought it´s relevant :oops:
Last edited by jrrdw on Sun Feb 02, 2014 6:42 pm, edited 1 time in total.
Reason: Fixed video.
CpTn_lAw wrote: :D "yay, me wanna make big multishot pnoob with 1000 psi foot pump compressor using diamond as main material. Do you think wet bread make good sealant? " :D
User avatar
bravootome
Specialist 3
Specialist 3
Romania
Posts: 334
Joined: Mon Oct 14, 2013 11:11 am
Has thanked: 1 time
Been thanked: 2 times

Sun Feb 02, 2014 1:57 pm

what is the maximum pressure you charged that propane red tank you got in your picture. I got one on my QeV and i put 25 bar, But i want more, like 30-35......
come undone
User avatar
Technician1002
Captain
Captain
Posts: 5189
Joined: Sat Apr 04, 2009 11:10 am

Mon Feb 10, 2014 8:27 pm

Highest pressure tested is 125, the highest a borrowed compressor could provide. It was a Hydrostatic test for safety. Safe to use now at 100 PSI.
MightyBlue
Private
Private
Posts: 3
Joined: Sun Sep 07, 2014 5:21 am
Location: United Kingdom
Contact:

Sun Sep 07, 2014 5:32 am

Great tutorial! will try this later!
IT Support Birmingham & Maintenance
Post Reply