Page 1 of 6
Airsoft Damage Challenge
Posted: Fri Nov 27, 2009 3:48 pm
by DYI
Just a simple challenge I came up with, no prizes involved other than bragging rights.
This afternoon, I launched a 0.12g airsoft round at a Canadian dime (92% steel, 5.5% copper, 2.5% nickel, 1.22mm thick). Predictably, it didn't go through. It did, however, leave an impressive
dent (considering the projectile).
So, here's the challenge: shoot your own airsoft gun, be it commercial or homemade, at a Canadian dime, or some roughly equivalent coin. No restriction on the mass of the round you use, so long as it's plastic, 6mm, and spherical. It would be interesting to see at what speed the coin starts bending.
Also, I personally guarantee a donation of $50 to anyone who actually manages to launch an airsoft round through a dime
Posted: Fri Nov 27, 2009 3:57 pm
by jackssmirkingrevenge
Dent? You made a little pixie cup!
fps?
Posted: Fri Nov 27, 2009 4:18 pm
by ALIHISGREAT
Did the BB bounce off? i can imagine that being a little dangerous!
Posted: Fri Nov 27, 2009 4:34 pm
by DYI
fps?
Did the BB bounce off? i can imagine that being a little dangerous!
I really couldn't say what the muzzle speed is, as I was using a new propellant configuration that I haven't tried before. I can say that there is 1" of wood between me and the launcher, and that, at these speeds, bouncing is not an issue - the round either punches through, and shatters into tiny pieces, or fails to punch through, and shatters into tiny pieces.
Posted: Fri Nov 27, 2009 4:36 pm
by cannon monkey
i will be happy to try this out
Re: Airsoft Damage Challenge
Posted: Fri Nov 27, 2009 5:21 pm
by SpudBlaster15
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Posted: Fri Nov 27, 2009 5:24 pm
by DYI
SpudBlaster15 wrote:Does it count if one uses 'magic silver dust' to propel the airsoft round?
Of course it does. Just don't tell us how you did it.
Posted: Fri Nov 27, 2009 6:10 pm
by sgort87
HOLY CHRIST! That dime doesn't HAVE a dent. It IS a dent! That's quite possibly the most impressive damage I've ever seen (relative to projectile size of course).
*shakes hand*
Posted: Fri Nov 27, 2009 6:58 pm
by rp181
You just wait until i finish the cap bank.... gonna be difficult to make a reliable spark gap though......
Im guessing solid propellants?
EDIT: read the pixie dust part....
Posted: Fri Nov 27, 2009 8:16 pm
by julktyl
It's amazing the BB didn't go all the way through with a crater like that. I might put a pic up when I finish my project. Should only be a day or two now...
Posted: Fri Nov 27, 2009 8:24 pm
by rp181
not really. round objects tend to dent alot before piercing.
Posted: Fri Nov 27, 2009 8:31 pm
by SpudBlaster15
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Posted: Fri Nov 27, 2009 8:48 pm
by hi
I dont think you can even shoot through a dime with a .22lr, so i dont think you could do it with an airsoft gun.
Posted: Fri Nov 27, 2009 8:56 pm
by rp181
that was most definitely not an ETG. Unless DYI changed his bank since i saw it on 4hv, 400 joules input will not do that.
I say ETC....or C.
Re: Airsoft Damage Challenge
Posted: Fri Nov 27, 2009 9:08 pm
by Ragnarok
DYI wrote:Predictably, it didn't go through.
Well then, it clearly wasn't going fast enough.
(Actually, I think the problem is more lack of mass and excess of velocity. Heavier BBs would likely help)