Dry ice
yeah, but ice makes pvc very brittle and its just simpler to use co2
searching for a modern day savior from another place,inclined toward charity,everyone's begging for an answer,without regard to validity,the searching never ends,it goes on and on for eternity
-Bad religion
-Bad religion
- singularity
- Corporal 5
- Posts: 982
- Joined: Mon Jun 26, 2006 10:53 pm
- Location: someplace
- Contact:
its easier to use air or co2 but if you really want to get some metal pipe and rig up a burst disc setup on one end and cap the other end, the burst disc would connect up to the barrel
be sure to check out my <a href="http://www.spudfiles.com/forums/ak-styl ... 9.html">AK Styled Vortex Gun</a> and my <a href="http://www.spudfiles.com/forums/at-4-t9627.html">AT-4 Rocket</a>
upcoming projects... finalized clip fed BBMG and ball point pen sniper
upcoming projects... finalized clip fed BBMG and ball point pen sniper
- Modderxtrordanare
- Corporal 2
- Posts: 686
- Joined: Mon Nov 20, 2006 1:22 pm
- Location: Texas
For every pound of dry ice you put in your chamber, it will expand into around 8 cubic feet of co2 gas. (8.3 to be exact)
Spudding since '05. Proud waster of plumbing and plumbing accessories.
-Wiki
-How-To: Modding a Sprinkler Valve
-Wiki
-How-To: Modding a Sprinkler Valve
depends on the temperature, so its kinda like propane in a way which stops raising in pressure at a certain temperature i.e 100psi @20* C (not accurate)frankrede wrote:Is there a maximum pressure before the pressure would stop rising
i believe its around 800psi at 25*C (not accurate either)
- potatoflinger
- Sergeant 2
- Posts: 1136
- Joined: Thu Nov 02, 2006 3:26 pm
- Location: Maryland
Actually, just last night I was thinking about using dry ice with a strafer, just put water and dry ice in a metal pipe with an air hose and a pop-off valve on it, that way I could make my strafer portable and have a pretty reliable compressed gas source. The only problem is that after shooting for a few seconds, I would have to wait for the pressure to build up again.
- Modderxtrordanare
- Corporal 2
- Posts: 686
- Joined: Mon Nov 20, 2006 1:22 pm
- Location: Texas
You could have a metal chamber and you fill it with dry ice and water, then when it builds sufficient pressure, it pops open the pop-off valve piloting a piston which leads to a bb barrel with a hopper or something.potatoflinger wrote:Actually, just last night I was thinking about using dry ice with a strafer, just put water and dry ice in a metal pipe with an air hose and a pop-off valve on it, that way I could make my strafer portable and have a pretty reliable compressed gas source. The only problem is that after shooting for a few seconds, I would have to wait for the pressure to build up again.
/rambling
Spudding since '05. Proud waster of plumbing and plumbing accessories.
-Wiki
-How-To: Modding a Sprinkler Valve
-Wiki
-How-To: Modding a Sprinkler Valve
If you used enough ice and water, the pressure should build to about 800 psi and stay there, because much of the dry ice would stay in its solid state due to the pressure not being able to rise any more. After you started using some of the gaseous CO2, more of the solid CO2 would sublimate to gas, replacing whatever gas was lost until the pressure came back up to 800psi. In a decent sized (and very strong) steel pipe, you could probably get even more CO2 than an equivalent sized cylinder filled with liquid CO2, and you wouldn't have to buy expensive tanks and regulators. Another plus is that you would have a strafer running on 800psi gas (unless you wanted to regulate pressure down). I think someone should try this. I probably will if I can get a hold of some dry ice, and 1000psi steel fittings.