camera stun gun

spudthug · Sun Apr 29, 2007 4:45 pm

well here is my home made disposable camera stun gun. it is simple yet very very loud and VERY hot when it goes off...the knife i have been discharging it on is getting marks on it and every time i pull my camera away it is like welded to the knife until i pul;l really hard..these are gret.. all u do it take the camera apart, go insdie pull out everything but the circut board, then break the falsh aprt and then break the bulb..after everything is out and borken hook 2 wires up to each end of the broken in half bulb..turn ur battery around to reverse it. press the button and discharge!

btw.. dont take it apart with the flash ready to go...i did..it sucked..it discharged once and thgen when i threw it into my other uhand it discharged again...it sucks! ill tell u right now it hurt like a mother effer!

hi · Sun Apr 29, 2007 4:56 pm

now all you need to do is put it in a small project box and your set. that spark looks so cool, if only i had a camera to take apart...... nice job.

super spuder · Sun Apr 29, 2007 5:00 pm

sweet. i will probly make something like that when i get around to making a combustion

spudthug · Sun Apr 29, 2007 5:03 pm

yea i have two of them because i had two old ones laying around.. but i was thinking about making a project combustion.. testing everything i can on it.. id put one of these on it, metered propane, comp fan, interchangable barrels, maybe burst disk, u tell me what else i should put on

Hotwired · Sun Apr 29, 2007 6:35 pm

One of these days I'm going to try to take a picture of my 12 camera flash capacitor bank discharging through a bit of metal.

I've been too nervous to do it so far because it would make a HELL of a bang

jimmy101 · Mon Apr 30, 2007 12:20 pm

HI: Just ask at the photo processing counter at your local grocery store. Usually they'll give you a camera or two for free. (They are supposed to return them to the factory to be refurbished but I suspect most places throw the camera away when they process the film.)

---------------

And remember, what Spudthug is describing is not a trigger system for a combustion spud gun. It's a stun gun. A potentially lethal one at that.

Hotwired · Mon Apr 30, 2007 5:48 pm

A camera or two?

I walked away from one place with a sack full

spudthug · Mon Apr 30, 2007 7:25 pm

damn!! where did u go lol..send me some or tell me whre ur store is!! i demand it!! or not..i have 2 stun guns already..im ok now

super spuder · Mon Apr 30, 2007 7:32 pm

this is a bit stupid, but how often do you have to replace the batteries in these?

spudthug · Mon Apr 30, 2007 7:34 pm

well.. i havent replaced mine yet. and it is jsut like a disposable camer, the batteries last forever with the flash. after u takle all the pics or if u have an empty one let the flash warm up and smack the bottom on ur hand, instant flash! hehe

super spuder · Mon Apr 30, 2007 7:38 pm

thanks. i am definately going to make one of these

spudthug · Mon Apr 30, 2007 8:51 pm

dont have the flash ready when u r going to first take it apart!! and never ever ever touch any part of the circuit board that u dont have to..it hurts like a biach!!

super spuder · Tue May 01, 2007 9:35 am

i will remember that

Hotwired · Tue May 01, 2007 10:57 am

Take the battery out and stick a screwdriver blade between the two wires coming out of the capacitor - it'll make a spark and remove the charge in the circuit.

jimmy101 · Tue May 01, 2007 12:35 pm

Hotwired wrote:Take the battery out and stick a screwdriver blade between the two wires coming out of the capacitor - it'll make a spark and remove the charge in the circuit.

Don't use a screwdriver you care about, you'll burn holes in it! (Please don't use your dad's best micro screwdriver!)

Use a "diggin-in-the-dirt-weed pulling screwdriver" or a piece of copper wire held in insulated pliers.

Don't short either of the wires on the big cap to anything else on the board. Very few of the boards components will handle the 300+ volts at several amps that might be stored in the cap.