How many shots per minute could a hybrid cannon reach with a mix of 5x of MAPP without getting too hot?
I want to construct a high powered cannon with a decent rate of fire and am unsure if I should go pneumatic or hybrid.
Any advice??
Shots per Minute
- MrCrowley
- Moderator
- Posts: 10078
- Joined: Fri Jun 23, 2006 10:42 pm
- Location: Auckland, New Zealand
- Been thanked: 3 times
Do you want this to be portable? If yes, go combustion. Both a hybrid and pneumatic will need to be pumped up and the hybrid needs to have fuel measured, burst disks put in place, ammo loaded, vented etc.
My burst disk hybrid used to get pretty hot with a terrible rate of fire (perhaps a shot every 5-10min) with a maximum of about 5 shots a day. The burst disks can be a pain in the ass so it might be better to go with a piston hybrid. Still need to vent it, fuel it, pump it up, load the ammo, configure the piston (air spring?) etc. I think either SB15 or SpudFarm were getting a single shot a minute.
What do you define as high powered? An advanced combustion will perform the same as some pneumatics. You can even out-peform 2" piston valved cannons with a combustion.
My burst disk hybrid used to get pretty hot with a terrible rate of fire (perhaps a shot every 5-10min) with a maximum of about 5 shots a day. The burst disks can be a pain in the ass so it might be better to go with a piston hybrid. Still need to vent it, fuel it, pump it up, load the ammo, configure the piston (air spring?) etc. I think either SB15 or SpudFarm were getting a single shot a minute.
What do you define as high powered? An advanced combustion will perform the same as some pneumatics. You can even out-peform 2" piston valved cannons with a combustion.
- jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
What specifications are you aiming for in terms of calibre and size, and what would you define as a suitable rate of fire - and rather importantly, what's your budget?
You can avoid burst disks using a piston, there are ways around these things... but compared to making a semi/auto pneumatic, it is indeed more complicated.
As suggested above, cartridges should be considered. My mini hybrid gets very warm after just one shot, firing several shots per second would probably set fire to the epoxy
Both a hybrid and pneumatic will need to be pumped up and the hybrid needs to have fuel measured, burst disks put in place, ammo loaded, vented etc.
You can avoid burst disks using a piston, there are ways around these things... but compared to making a semi/auto pneumatic, it is indeed more complicated.
As suggested above, cartridges should be considered. My mini hybrid gets very warm after just one shot, firing several shots per second would probably set fire to the epoxy

hectmarr wrote:You have to make many weapons, because this field is long and short life
I defiantly want it to be portable, but it doesn’t have to be tiny. An attached paintball tank wouldn’t bother me at all, but I don‘t want to be walking around with a fire extinguisher or scuba tank.
I’m looking at using 1.5” spherical projectiles as ammunition, specifically miniature tennis balls . I want to go pneumatic, but I don’t know how many shots I’ll be able to pull off with a full paintball tank. I don’t want to have to constantly be refilling the tank, that is why I was thinking about hybrid. An ideal firing rate would be at least four shots per minute, but preferably closer to ten. My budget is no higher than $200. When I said “high powered” I was thinking at least the speed of a paintball gun. I am planning on incorporating some sort of cartridge as well.
I’m looking at using 1.5” spherical projectiles as ammunition, specifically miniature tennis balls . I want to go pneumatic, but I don’t know how many shots I’ll be able to pull off with a full paintball tank. I don’t want to have to constantly be refilling the tank, that is why I was thinking about hybrid. An ideal firing rate would be at least four shots per minute, but preferably closer to ten. My budget is no higher than $200. When I said “high powered” I was thinking at least the speed of a paintball gun. I am planning on incorporating some sort of cartridge as well.
Stay Frosty,
Wilson276
Wilson276
- jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
A combustion cartridge might serve you well in this case 

hectmarr wrote:You have to make many weapons, because this field is long and short life