I also made a propane tank holder from 4" ABS, and ran the hose around the gun. I also clamped the hose down to keep it from flapping around.
The Hybrid- 10/05
OK, got some improvements! I mounted the cannon to a piece of 3/4" plywood, and got a better paint job for it. The gun is clamped to the board with those steel pipe brackets. It is extremely sturdy, and doesn't budge when firing. I still need a longer barrel, but I plan on getting one tomorrow or Sunday. I also recorded pictures of random crap that I shot up.
I also made a propane tank holder from 4" ABS, and ran the hose around the gun. I also clamped the hose down to keep it from flapping around.
I also made a propane tank holder from 4" ABS, and ran the hose around the gun. I also clamped the hose down to keep it from flapping around.
- Attachments
-
- The beast!
-
- A side view. I also clamped the BBQ igniter wire inside the steel bracket to keep it from flying around and poking me.
-
- Here you can see the front of the the gun and propane tank.
-
- Before.
-
- After.
-
-
- The hole left by a battery. It went through the motherboard, flew 20 feet, then went through my 1" wood fence, SIDEWAYS.
-
- A deadified motherboard.
-
- Guess what this is.
- paintedhybrid 006.jpg (23.18 KiB) Viewed 8798 times
-
- It's a battery!
-
- An exit hole.
-
- An exit hole.
-
- Steel BB buckshot, tore through 3 soda cans in a row and all were embedded in my fence.
Last edited by noname on Sun Oct 05, 2008 9:50 pm, edited 4 times in total.
I think I need to cement my barrel onto the male adapter, it gets blasted off at 4x and above mixes now. 
The inside of the barrel is also singed black, and gets orange-ish brown as it gets further. I've been shooting random stuff with batteries and ball bearings almost all morning, and I can send a ball bearing through over 2" of wood. All I need is a 20 foot barrel, and then I can have some supersonic fun!
The inside of the barrel is also singed black, and gets orange-ish brown as it gets further. I've been shooting random stuff with batteries and ball bearings almost all morning, and I can send a ball bearing through over 2" of wood. All I need is a 20 foot barrel, and then I can have some supersonic fun!
very cool. did you ever figure out what was wrong with the first one?
searching for a modern day savior from another place,inclined toward charity,everyone's begging for an answer,without regard to validity,the searching never ends,it goes on and on for eternity
-Bad religion
-Bad religion
Mopherman, this is the first one. I just redesigned it. The very first design had a tank that I would fill with a hybrid mixture, then hook up the the ignition chamber with an air chuck. The second design had a larger propane meter that kept the fuel from mixing, so it wouldn't work.
I really want to see if it'll shoot through 8" PVC, but I really don't feel like getting hit by a ricochet.
I really want to see if it'll shoot through 8" PVC, but I really don't feel like getting hit by a ricochet.
It should break it. i was able to with a sprinkler valve marble cannon.noname wrote: I really want to see if it'll shoot through 8" PVC, but I really don't feel like getting hit by a ricochet.
searching for a modern day savior from another place,inclined toward charity,everyone's begging for an answer,without regard to validity,the searching never ends,it goes on and on for eternity
-Bad religion
-Bad religion
it put a hole with spiderweb cracks throughout the pipe. judging by the power of you gun and the time that pipe has spent out in the sun, it'l probly shatter.noname wrote:I'll try it some time, most likely. The gun can shoot through a sheet of 3/8" ABS with no problem.
Did your gun crack it, or put a hole in it, or shatter it, or what?
Be safe though
theres pics half way down the page with rmich's gun
searching for a modern day savior from another place,inclined toward charity,everyone's begging for an answer,without regard to validity,the searching never ends,it goes on and on for eternity
-Bad religion
-Bad religion
According to a GGDT estimate, the gun shoots at somewhere around 1450 fps, with an 8 gram ball bearing projectile.
Not sure how fast it shoots with batteries, but I shot one through a 40 page book, then it kept going and made a hole in my fence (1" plywood). The insane thing is, the battery was SIDEWAYS, leaving a rectangular hole! I'll see if I can get some damage pics up.
Not sure how fast it shoots with batteries, but I shot one through a 40 page book, then it kept going and made a hole in my fence (1" plywood). The insane thing is, the battery was SIDEWAYS, leaving a rectangular hole! I'll see if I can get some damage pics up.
-
SpudBlaster15
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 5:12 pm, edited 1 time in total.
I don't think I'm going to make it hand held. I've gone through too much trouble too have it stop working because of having the volume of the meter changed by 1 mL or something like that. I'll make a tiny pistol hybrid at some point or something.
A 16 foot barrel will be made today, hopefully.
A 16 foot barrel will be made today, hopefully.
-
SpudBlaster15
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 5:11 pm, edited 1 time in total.