First off, sorry if this is against forum rules, I know exploding ammo is and Im not sure about targets. These are fun and easy targets for bb caliber guns.
[youtube][/youtube]
Flaming Targets
- Attachments
-
- This is my high voltage generator, its the transformer from a fly zapping lantern, Just connect the two wires to your two nails, and make sure it sparks.
-
- Put them together like this, leaving a small spark gap between the nails. You clip the bottom of your balloon into the document clip.
-
- To build the holder you need a lump of wood, two nails, a document clip, and a way of attaching the document clip.
-
- Just fill up a water balloon or any balloon then tie the bottom.
-
- This was left over from my advanced combustion gun, the valve part of a propane torch and a hose connector.
-
- Hopefully your end result. (if your a good shot :) )
- hit.jpg (24.5 KiB) Viewed 4379 times
Last edited by jor2daje on Fri Jun 19, 2009 9:14 pm, edited 1 time in total.
-
MountainousDew
- Specialist 2
- Posts: 230
- Joined: Tue Apr 14, 2009 6:06 pm
I think this falls into a grey area in the rules, but nonetheless this is a cool idea.
If I understand correctly, there is a continuous spark behind the balloon so when it pops it propane is released, and the propane ignites into a fireball...
I like it!
Edit: Videos would be very helpful for "research"...
If I understand correctly, there is a continuous spark behind the balloon so when it pops it propane is released, and the propane ignites into a fireball...
I like it!
Edit: Videos would be very helpful for "research"...
Last edited by MountainousDew on Fri Jun 19, 2009 9:15 pm, edited 1 time in total.
<a href="http://s709.photobucket.com/albums/ww95 ... =MDSig.jpg" target="_blank"><img src="http://i709.photobucket.com/albums/ww95 ... /MDSig.jpg" border="0" alt="Photobucket"></a>
or, you couldn just take a regular target, drench it in naptha, and drop a match on it 
, nice idea though!
EDIT: that might be one of the coolest vids Ive seen in a while, congrats!!
, nice idea though!EDIT: that might be one of the coolest vids Ive seen in a while, congrats!!
"You can't be friends with anyone if you aren't friends with yourself."
"I'd rather be hated for who I am, than loved for who I'm not." -André Gide
Give me a lever long enough, and a fulcrum on which to place it and I shall move the world.
–Archimedes
Defeat is always momentary.
–Carl Denham
Current Project: None, I'm in Spudremission.
"I'd rather be hated for who I am, than loved for who I'm not." -André Gide
Give me a lever long enough, and a fulcrum on which to place it and I shall move the world.
–Archimedes
Defeat is always momentary.
–Carl Denham
Current Project: None, I'm in Spudremission.
-
THUNDERLORD
- Sergeant 3
- Posts: 1264
- Joined: Fri Mar 28, 2008 1:42 pm
At first I thought the the electricity (spark gap) was on when you clip the balloon.
But it should be obvious to anyone not to do that.
Reminded me of This Awesome vid!!!
I am going to watch that again!
(Seroiusly I LOL'd just now at that reminder to be careful). 8)
But it should be obvious to anyone not to do that.
Reminded me of This Awesome vid!!!
I am going to watch that again!
(Seroiusly I LOL'd just now at that reminder to be careful).
8)-----SPEED,STRENGTH, AND ACCURACY.-----
"Procrastination" is five syllables for "Sloth".
Theopia 8)
Born To Be Alive!
"Procrastination" is five syllables for "Sloth".
Theopia 8)
Born To Be Alive!
-
mobile chernobyl
- Corporal 3
- Posts: 759
- Joined: Sun Dec 03, 2006 11:53 am
- Been thanked: 8 times
lol I used to make detonating balloons just like this, only with correct mixture of oxy and acetylene, only they were usually "triggered" not shot at. Amazing what they can do to metal cans, microwaves.. etc. Definitely the cheapest form of "rapid disassembly" I've done.
-
inonickname
- First Sergeant 4
- Posts: 2606
- Joined: Sun Dec 07, 2008 3:27 am
Ever done a rubbish bin? We tried an old car at the tip once, spent a LONG time duct taping every little hole around the doors and such.mobile chernobyl wrote:lol I used to make detonating balloons just like this, only with correct mixture of oxy and acetylene, only they were usually "triggered" not shot at. Amazing what they can do to metal cans, microwaves.. etc. Definitely the cheapest form of "rapid disassembly" I've done.
Was fairly loud..
Pretty cool though, have any problems with the electrodes/spark next to the balloon?
PimpAssasinG wrote:no im strong but you are a fat gay mother sucker that gets raped by black man for fun
-
mobile chernobyl
- Corporal 3
- Posts: 759
- Joined: Sun Dec 03, 2006 11:53 am
- Been thanked: 8 times
Is that car one online as a video? I've seen a few people do the same thing with the cutting torch setups at most junk yards lol.inonickname wrote: Ever done a rubbish bin? We tried an old car at the tip once, spent a LONG time duct taping every little hole around the doors and such.
Was fairly loud..
Pretty cool though, have any problems with the electrodes/spark next to the balloon?
We mostly would only use balloons as the pressure was not a bid deal as long as the mixture was stoichiometric - you would get a Det and not a deflag.
we did like metal 5 gallon cans and plastic 5 gallon cans - it would reduce them to rubish usually. Also old mailboxes, and other sheet metal containers were fun. One of the funniest was filling a projection big screen TV - that was one of the most High Def action scenes i've ever seen lol!
I've recently been thinking of making a Det-gun similar to what they use on farming land and avalanche control, but use it to propel stuff lol.
-
POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
I think that most of us thought about somehting like this in the past.. but AFAIK you are the first one who showed a fully working prototype
nice... I like it
nice... I like it
Children are the future
unless we stop them now
unless we stop them now
Its cool, and even better, its safe (in terms of exploding targets that is).
Can't the balloon pop when it gets sparked?
Can't the balloon pop when it gets sparked?