First of all, does anyone have the GGDT specs for a McMaster 3/4" QEV? I couldn't find any, so I took one apart to measure my own, and so far I have:
Seat Diameter: 1.25 in
Dead Volume: 1.178 in^3
Piston Diameter: 1.75 in
Piston Mass: 8.3 grams
Pilot Volume: .98 in^3
What does "vent diameter" refer to, and how do I find the flow coefficient? Also, if anyone has numbers to check against mine that would be great.
QEV in GGDT
This thread suggests the Cv coefficient for McMaster-Carr's 3/4 inch valve is about 6: http://www.spudfiles.com/forums/dual-qe ... 12691.html
yes, using a Cv of ~6 worked well in predicting the velocity over a range of pressures for my tests.
please keep in mind that the 3/4" QEV was piloted by a smaller 1/4" QEV (as described in the post mentioned above), and that seemed to make a big difference in the way the 3/4" fired.
i didn't do any testing to estimate the Cv of the 3/4" QEV without using the smaller 1/4" QEV as a pilot, but do remember that, when using just a blowgun to pilot the 3/4" QEV, that the velocities were reduced, and the audible report of the GG was not nearly as "snappy", loud, or as satisfying as when the sucker is opened up fast...
hope this helps
please keep in mind that the 3/4" QEV was piloted by a smaller 1/4" QEV (as described in the post mentioned above), and that seemed to make a big difference in the way the 3/4" fired.
i didn't do any testing to estimate the Cv of the 3/4" QEV without using the smaller 1/4" QEV as a pilot, but do remember that, when using just a blowgun to pilot the 3/4" QEV, that the velocities were reduced, and the audible report of the GG was not nearly as "snappy", loud, or as satisfying as when the sucker is opened up fast...
hope this helps
- john bunsenburner
- Sergeant 5
- Posts: 1446
- Joined: Sun Oct 19, 2008 5:13 am
I hope you dont mind the little hijack of this thread but: What exactly is the valve coefficiency of a hammer valve and what is its seet diameter(is it just the ID of the pipe used or somehting else?)
"Did you ever stop to think that out of the seven deadly sins envy is the only one which doesn't give the sinner even momentary pleasure"-George Will
john, you might want to start a new thread when discussing a new topic - many people will pass by this thread title if they have read it before or aren't interested in the title, in which case, most forum members won't see your question...
unfortunately, i don't have experience with hammer valves. what manufacturer/model are you asking about? do you have a link to a spec. sheet, or even pictures? or is it a custom valve? ...just information to consider posting along with your new forum topic...
cheers,
peeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeto
unfortunately, i don't have experience with hammer valves. what manufacturer/model are you asking about? do you have a link to a spec. sheet, or even pictures? or is it a custom valve? ...just information to consider posting along with your new forum topic...
cheers,
peeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeto
- MrCrowley
- Moderator
- Posts: 10078
- Joined: Fri Jun 23, 2006 10:42 pm
- Location: Auckland, New Zealand
- Been thanked: 3 times
That's not the point...twizi wrote:yes it does have better preformance

He is saying that everyone says 3/4" QEV's out-perform 1" sprinkler valves, but using the parameters given for the 1" orbit sprinkler valve and the 3/4" McMaster QEV, the QEV only has 75% of the velocity of the sprinkler valve cannon.
You can't just agree that QEV's have better performance, next time think before you post or I will just delete it.
Back on topic, that is pretty interesting. I'll have to run in through GGDT and have a look for myself, probably a number of factors to think about. I wonder who ever said 3/4" QEVs are better in the first place...I've never compared the two myself before.
- daberno123
- Corporal
- Posts: 594
- Joined: Mon Nov 19, 2007 5:56 pm
- Location: Ohio
Everyone assumes a 3/4" QEV will outperform a 1" sprinkler valve based on the assumption that the QEV has a much better flow path than the sprinkler valve.
That being said, I'd like to see someone take some screen shots and post them so everyone can see.
That being said, I'd like to see someone take some screen shots and post them so everyone can see.