2" Union Burst Disks
I was wondering, since I never got the opportunity to test out a soda can cutout to see its bursting pressure, has anybody ever done so with a 2" union?
The new hybrid design will be a large 2" hybrid. I've heard that problems may arise when so many burst disks are required. It's been told you must grind the edges off the inside of a union to fit a gasket, and that it will make fitting so many soda can disks airtight.
The thickness of 10 pieces is 0.97 millimeters. Will such a gap in the union be overcome by simply torquing the union a little more? The predicted mixes I may achieve (depending on burst disks), will be anywhere from 5x to 20x.
The new hybrid design will be a large 2" hybrid. I've heard that problems may arise when so many burst disks are required. It's been told you must grind the edges off the inside of a union to fit a gasket, and that it will make fitting so many soda can disks airtight.
The thickness of 10 pieces is 0.97 millimeters. Will such a gap in the union be overcome by simply torquing the union a little more? The predicted mixes I may achieve (depending on burst disks), will be anywhere from 5x to 20x.
-
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Thu Jul 15, 2021 1:44 am, edited 1 time in total.
-
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Thu Jul 15, 2021 1:44 am, edited 2 times in total.
I ordered a 2" 2kpsi union from Murray Equipment Inc just a two days ago.
Would it be possible to just grind off the barrel side of the union, so the other tapered side holds the gasket? Or if both sides are grinded off, the pipe on the chamber side will hold the gasket inside the union.
Would it be possible to just grind off the barrel side of the union, so the other tapered side holds the gasket? Or if both sides are grinded off, the pipe on the chamber side will hold the gasket inside the union.
- Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
you could give them a call and ask if the union you ordered has tapered faces
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
Or I could just wait a few days. If it isn't tapered, then I guess I'm all good, only need a rubber washer.
I'm thinking of buying a few 1/4 thick neoprene squares, and then cut disks out using an X-Acto knife. That just gave me a great idea:
Instead of using rubber to make seals in the union. Couldn't we use thick rubber to be the burst disk itself?
I'm thinking of buying a few 1/4 thick neoprene squares, and then cut disks out using an X-Acto knife. That just gave me a great idea:
Instead of using rubber to make seals in the union. Couldn't we use thick rubber to be the burst disk itself?
- Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
rubber wouldn't burst very well, it would make a small hole in the middle and the heat from the mix will melt it away a bit more but it wont be very fast like say layered aluminium foil and rubber disks would be expensive
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
- Technician1002
- Captain
- Posts: 5189
- Joined: Sat Apr 04, 2009 11:10 am
Make one. Use a piece of iron pipe and cut a cutting edge on it. I launched a piece of conduit with a sharpened edge at a washing machine and it performed well. A washing machine is a little thicker than a pop can.whoa044 wrote:Yeah, rubber splits, rather than just falling apart like thin metal.
Does anybody know where I can get 2" circular punches?
He uses his QDV, which is a type of piston valve.
Measure the diameter inside of the area in the union where the BD will go, and find something round and metal at the hardware store with the same diameter.
Measure the diameter inside of the area in the union where the BD will go, and find something round and metal at the hardware store with the same diameter.
POLAND_SPUD wrote:even if there was no link I'd know it's a bot because of female name
So I finally got my forged steel fittings in the mail from MEI. The box weighed, by my guess, around 30 pounds. This included all 2" fittings: 2, 6" nipples. a tee, union, and three bushings.
I swear, that union was huge:
I can see how the inside is tapered, if anybody is interested, I have a short video showing how large the thing is, and what the insides look like.
I swear, that union was huge:
I can see how the inside is tapered, if anybody is interested, I have a short video showing how large the thing is, and what the insides look like.
- Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 7 times
Holy hell! That thing is a monster. Good luck on the launcher, can't wait to see it!
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!