How do i make this semi auto?

Goats spudz · Tue Aug 30, 2011 2:20 am

http://www.technobotsonline.com/quick-e ... -4-in.html

jackssmirkingrevenge · Tue Aug 30, 2011 2:27 am

http://www.ebay.com/itm/Slide-shut-off- ... 1c18e5e48e

Goats spudz · Tue Aug 30, 2011 2:29 am

jackssmirkingrevenge wrote:http://www.ebay.com/itm/Slide-shut-off- ... 1c18e5e48e

i mean like a shot every time you press the trigger, couldn't i use a blowgun

jackssmirkingrevenge · Tue Aug 30, 2011 2:44 am

You need to mod the QEV for chamber feeding if you're using a blowgun, basically unscrew it, poke a small hole through the diaphragm (NOT the part that covers the seat, between the seat and the valve wall) and put a small spring between the diaphragm and the rear of the valve.

Goats spudz · Tue Aug 30, 2011 3:29 am

<3 for jsr but when it fires, the shot isnt like a bang its a hiss

wyz2285 · Tue Aug 30, 2011 3:31 am

http://www.youtube.com/watch?v=0BXPoN0zrCQ
mod the qev like this

jackssmirkingrevenge · Tue Aug 30, 2011 3:31 am

Hmmm... I said poke a small hole, you didn't go an poke a big one did you?

wyz2285 · Tue Aug 30, 2011 3:34 am

no, I still want the qev to be sensitive

Goats spudz · Tue Aug 30, 2011 3:37 am

i think it may have been a little big shall i tape over it and poke a smaller one through the tape (insulation tape)

jackssmirkingrevenge · Tue Aug 30, 2011 4:05 am

Goats spudz wrote:i think it may have been a little big shall i tape over it and poke a smaller one through the tape (insulation tape)

I don't think tape will cut it, epoxy

remember it doesn't need to be more than 1mm diameter.

Goats spudz · Tue Aug 30, 2011 4:17 am

I covered the hole and changed to a 1.5mm drill bit (the smallest that will fit in the chuck) and put the hole in the right place this time (i put the big one that's covered where the thin rubber is :L) and it works but with my bike hand-pump i can get 2 shots from it, if i get a fridge compressor and take it to about 55 bar will i get lots of high power shots?

jackssmirkingrevenge · Tue Aug 30, 2011 4:25 am

http://www.spudfiles.com/forums/b2tb-sa ... 14817.html

Crna Legija · Tue Aug 30, 2011 4:58 am

Goats spudz wrote:I covered the hole and changed to a 1.5mm drill bit (the smallest that will fit in the chuck) and put the hole in the right place this time (i put the big one that's covered where the thin rubber is :L) and it works but with my bike hand-pump i can get 2 shots from it, if i get a fridge compressor and take it to about 55 bar will i get lots of high power shots?

can you post it before you take it to 55bar, that kind of pressure is nothing to be playing with.

Goats spudz · Tue Aug 30, 2011 6:53 am

Crna Legija wrote:
Goats spudz wrote:I covered the hole and changed to a 1.5mm drill bit (the smallest that will fit in the chuck) and put the hole in the right place this time (i put the big one that's covered where the thin rubber is :L) and it works but with my bike hand-pump i can get 2 shots from it, if i get a fridge compressor and take it to about 55 bar will i get lots of high power shots?
can you post it before you take it to 55bar, that kind of pressure is nothing to be playing with.

most of it is high pressure hydraulic fttings and the tank is rated to 3000 psi

jackssmirkingrevenge · Tue Aug 30, 2011 6:56 am

Goats spudz wrote:most

... but like a chain, it's only as strong as the weakest component

How do i make this semi auto?

Create an account or sign in to join the discussion

Create an account

Sign in

Login • Register