Sam's Hybrid Plans H.V.S-1
-
SpudBlaster15
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 4:44 pm, edited 1 time in total.
-
SpudBlaster15
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 4:43 pm, edited 1 time in total.
I know that the pipe is steel, but I had always thought that the fittings were malleable iron (the names malleable or cast IRON are misleading, as they both contain a percentage of carbon. Malleable iron contains significantly less carbon than steel, and cast iron contains quite a bit MORE carbon than steel does).
If the fittings are actually steel, this means that I could theoretically take my triggered burst disk gun to 300psi with CO2. I wonder how loud that would be
If the fittings are actually steel, this means that I could theoretically take my triggered burst disk gun to 300psi with CO2. I wonder how loud that would be
-
SpudBlaster15
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 4:43 pm, edited 1 time in total.
-
Modderxtrordanare
- Corporal 2
- Posts: 686
- Joined: Mon Nov 20, 2006 1:22 pm
- Location: Texas
Isn't 4.03% more accurate?SpudBlaster15 wrote:Frank, the proper propane quantity per atmosphere of air is 4.2%, not 4.7%. For a 4x hybrid, you should inject 16.8% of it's volume in propane.
Spudding since '05. Proud waster of plumbing and plumbing accessories.
-Wiki
-How-To: Modding a Sprinkler Valve
-Wiki
-How-To: Modding a Sprinkler Valve
-
SpudBlaster15
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 4:43 pm, edited 1 time in total.
-
spudthug
- Corporal 5
- Posts: 936
- Joined: Mon Feb 26, 2007 9:02 pm
- Location: johnsonburg, Pa USA
- Contact:
when u join them with a couple the coupler is going to add another 2 inches..so you are going to have an 8 inch chamber...
4" piston valved cannon-half done..( i spilt my cement...)
Hybrid- 75% done. need to build propane holder and drill/tap sparkplug hole..
Hybrid- 75% done. need to build propane holder and drill/tap sparkplug hole..
well, the nipples are theaded almost all of the way into the coupler so theres only a .75 gap.....so the overall chamber size it more like 7, plus the recucing the sockets....its gunna be pretty big.....but pretty powerfull aswel...
what you guys think of my progress so far..
what you guys think of my progress so far..
