Golfball Gun Target/Backstop
-
clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
Well this is my new target I made to shoot my golfball gun at. Its made from a printer box and stuffed with coke cans,newspaper, styrofoam, water bottles, and old towels. The outside is covered with an old sheet. So far Ive tested it by shooting it with my golfball gun and bbmg at 45 psi each, Ill test it at higher pressures tomorrow. Any ideas about water proofing it. I considered covering it with a sheet of plastic but figured the golfball would punch through it. It probably weighs around 30 pounds.
- Attachments
-
-
-
Last edited by clemsonguy1125 on Sat Feb 20, 2010 6:45 pm, edited 1 time in total.
-
Lockednloaded
- Staff Sergeant
- Posts: 1566
- Joined: Thu Sep 03, 2009 9:38 pm
- Location: Texas, USA
- Been thanked: 7 times
Its amazing you'd go into this much work for a target 
unless of course it is a back stop meant to stop the golf balls
For the water proofing, just wrap it completely in duct tape
~lnl~
unless of course it is a back stop meant to stop the golf balls
For the water proofing, just wrap it completely in duct tape
~lnl~
-
clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
Well I spent about an hour on it, its more of a backstop I guess since I made it not for the golfballs to penatrate, I set it behind a piece or rotten wood and it completly stops the golfball, as for covering it with duct tape this wont work for the bbmg since the bbs are small and punch cleanly through.Lockednloaded wrote:Its amazing you'd go into this much work for a target
unless of course it is a back stop meant to stop the golf balls
For the water proofing, just wrap it completely in duct tape
~lnl~
Thanks for the quick reply
-
clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
The printer is not in there but I have an old scanner that I can destroy once I remove a couple of parts I want such as the motor.jrrdw wrote:I hope there is a Epson printer in there...
-
clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
Ive already removed them along with a small motor a couple leds and some metal rods, and sheet of glassjrrdw wrote:How about the optic's that do the scanning?
Off topic.... My HP $50 scanner broke the other day, i called tech support today....sunday.... and they sent me a gift certificate worth $90
Woo HP!!!!
Back on topic....
Ya... nice backstop. that should stop most high velocity golf balls. lol
What kind of muzzle velocity are you getting from a golf ball??
Btw.... i tried to use an old, beat up mattress as a bouncy ball backstop... the ball went through.... hit the concrete wall... and went through the mattress again backwards.... and then landed in a box right near my feet. lol. so be careful.
Woo HP!!!!
Back on topic....
Ya... nice backstop. that should stop most high velocity golf balls. lol
What kind of muzzle velocity are you getting from a golf ball??
Btw.... i tried to use an old, beat up mattress as a bouncy ball backstop... the ball went through.... hit the concrete wall... and went through the mattress again backwards.... and then landed in a box right near my feet. lol. so be careful.
jackssmirkingrevenge wrote:I wonder... if you put flammable vapours inside a lady... could you get her to diesel?
POLAND_SPUD wrote:Anything is possible with the proper 3-way valve.
-
clemsonguy1125
- Sergeant 5
- Posts: 1485
- Joined: Tue Jul 21, 2009 4:00 pm
- Location: East Coast
No idea, I dont have a chrono, all I know it this thing can shoot through plywood at 40 psi from 50 feet, thanks for the warningjhalek90 wrote:Off topic.... My HP $50 scanner broke the other day, i called tech support today....sunday.... and they sent me a gift certificate worth $90
Woo HP!!!!
Back on topic....
Ya... nice backstop. that should stop most high velocity golf balls. lol
What kind of muzzle velocity are you getting from a golf ball??
Btw.... i tried to use an old, beat up mattress as a bouncy ball backstop... the ball went through.... hit the concrete wall... and went through the mattress again backwards.... and then landed in a box right near my feet. lol. so be careful.